Hyundai Models

APPENDIX – C Version 2.0 Publish Date May 2021

PageModelCode Model

Technical Bulletin#

Hyundai Model Revision Date (YYMM) Rev#

COMPACTS

2 HC Accent H HC 1707 R4 HHC1707R4

3 PD Elantra H PD 1703 R3 HPD1703R3

4 CN7 ElantraGT H CN7 2007 R1 HCN72007R1

5 AE IONIQ Hybrid H AE 1611 R6 HAE1611R6

6 JS Veloster H JS 1803 R4 HJS1803R4

SEDANS

7 DN8 Sonata H DN8 1910 R2 HDN81910R2

8 DN8 HEV Sonata HEV H DN8 HEV 1910 R0 HDN81910R0

CROSSOVERS

9 OS, OSEV Kona H OS, OSEV 1710 R3 HOS1710R3

10 FE NEXO FCEV H FE 1804 R4 HFE1804R4

11 TL Tucson H TL 1906 R4 HTL1906R412 NX4 Tucson H NX4 2102 R1 HNX42102R0

13 TM Santa Fe H TM 1808 R4 HTM1808R4

14 TM HEV Santa Fe H TM HEV 1808 R0 HTMHEV18R0

15 LX2 Palisade H LX2 1902 R5 HLX21902R5

16 QX Venue H QX 1907 R2 HQX1907R2

RELATED TECHNICAL HANDLING BULLETINS

17 ALL Seat Belts H ALL 0919 R1 GHK1902R1

18 ALL Hybrids must be turned-off H ALL 0825 R0 GHK2008R019 ALL No Starts H ALL 0720 R0 GHK2007R0

20 ALL Covid-19 Protocol H ALL 0720 R1 GHK20716R1

21-23 ALL Undelivered vehicles H ALL 1020 R0 GHK2010R0

24 ALL STI – Key control process H ALL 1020 R0 GHK2009R0

APPENDIX CVehicle Delivery Quick Reference Guide

KEY PLACEMENT All keys must be placed in Cup Holder As a theft prevention measure, remove all keys from the last vehicle loaded on trailer

Technical BulletinNUMBER: DATE:

HYUNDAI KIA MODEL YEAR: MODEL CODE:

SUBJECT:

17305 Von Karman, Suite 200 Irvine, CA 92614

QUALITY (714) 435-2990 Page 1 of 1

Revision R4

COMMENTS:

TRUCK HAULAWAY a. Upper deck: Approved for all upper deck positions. Avoid using wheel pocket extensions in the head

rack position due to insufficient undercarriage clearance.b. Lower deck: Approved for all lower trailer positions. Use caution over the trailer’s tandem wheels and

ramp break-over points due to reduced undercarriage clearance.c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle

securement is strictly prohibited. Wheel straps may contact tire tread surfaces only.d. Soft-tie side pulls and strap contact with undercarriage components are strictly prohibited.e. Caution: Reduce vehicle loading speeds when approaching or exiting skids, trailer tandems and ramp

break-over points.

RAIL LOADING a. Tri-level rail cars: Approved for all loading positions. Low-profile chocking systems are the preferred

chock type. Hyundai Accents with installed mudguards are excluded from the standard railcar A5 position aschock clearance can be less than the required AAR 2” (5.1 cm) minimum spacing.

b. AutoMax railcars use caution in the A3 and A6 positions. Accents having installed mudguards theirchock clearance may be less than the required 2” (5.1 cm) minimum AAR spacing requirement. Placethese vehicles on ‘B’ or ‘C’ decks.

c. Bi-level rail cars: may be utilized in the event of a tri-level railcar shortage. The Hyundai Accent isapproved for all loading positions. Place chock setting in the highest setting that will maintain aminimum of 2” (5.1 cm) clearance between the chock body and any vehicle component. HoldenGrip-Lock® chocks are not recommended securements, as chock clearance can fall below the requiredAAR standard.

GENERAL a. a. Hyundai Accent has limited ground clearance of approximately 5.5 inches (14.0 cm).b. b. Always wear a seatbelt when operating vehicle.

c. c. The Accent must be shipped with its front tires in the straight forward position, automatic transmissiond. placed in “Park” or in ‘first gear’ for manual transmissions and its parking brake fully engaged.

e. d. Always wear a seatbelt when operating vehicle.f. e. Use caution entering or exiting steep ramp angles, front fascia damage can occur at speeds in excessg. of 2.5 mph.

h.

*All weights and dimensions are approximate and are subject to change.

X

HHC1707R4 07 Jul 2017

Feb 20142021 HC

MY2021 Hyundai Accent Sedan

Spec ifica tions

MY2021 ACCENT

SE, SEL and Limited

1.6L DPI DHOC 16 - V Inline 4 - cylinder D- CVVT 120 hp @ 6 ,300 rpm (est. )

Whee lbase 101.6 in.

Overa ll Length 172 .6 in.

Overa ll Width (exc ludes mirrors) 68 .1 in.

Overa ll He ight 57 .1 in.

Ground Clea rance 5 .5 in.

Curb we ight M/T IVT (Auto)

2 ,502 lbs. 2 ,679 lbs.

*All weights and dimensions are subject to change without notice.

Technical BulletinNUMBER: DATE:

HYUNDAI KIA MODEL YEAR: MODEL CODE:

SUBJECT:

7305 Von Karman, Suite 200 Irvine, CA 92614

QUALITY 714-435-2990

Page 1 of 1 Revision 1

Specifications

MY2021 Hyundai Elantra (CN7) 2.0 L

Wheelbase: 107.1" 272.03 cm

Length: 184.7" 469.14 cm

Height: 55.7" 141.48 cm

Width: 71.9" 182.63 cm

Tires/wheels: 15", 16", 17" 38.10, 40.64, 43.18 cm

Tires/wheels: N Series 18 " 45.72 cm

Min. Ground Clearance: 6" 15.24 cm

Curb weights: 2,725 - 3,990 lbs. Limited HEV (DCT) 1,236.04 - 1,809.83 kg

Specifications2.0L SE, SEL Value, & Limited Eco & 1.6T Sport2.0L 4 D-CVTT 147hp @ 6,200 rpm 1.4L DOCH 128hp @ 5,500 rpm & 1.6L T 201 hpCurb Weight: SE 2,844 lbs (1,290.02 kg) Curb Weight: Sport 3,131 lbs. (1,420.20 kg) Max.Wheelbase: 106.3 in. (270.00 cm) Wheelbase: 106.3 in. (270.00 cm) Length: 181.9 in. (462.03 cm) Length: 181.9 in. (462.03 cm)Width: 70.9 in. (180.9 cm) Width: 70.9 in. (180.9 cm) Height: 56.5 in. (143.51 cm) Height: 56.5 in. (143.51 cm)Wheels: 15 in. - 17 in. (38.1 - 43.18 cm) Wheels: 15 in. - 18 in. Alloy (38.01 - 45.72 cm)

* All weights and dimensions are approximate and are subject to change.

COMMENTS:

TRUCK HAULAWAY Upper deck: (Both Day and Sleeper Cabs): MY2021 Elantra (CN7) is approved for all upper deck positions.

a. Upper deck: Elantra’s upper deck restriction: regardless of the tractor or trailer’s manufacturer or the trailer’slength, the Elantra CN7 may only be loaded facing the forward direction in the trailer’s #1 headrack position.Close or use a high pocket wheel position in the trailer’s headrack to prevent front fascia or suspension damage.

b. Lower deck: (Both Day and Sleeper Cabs): MY2021 Elantra (CN7) is approved for all lower trailer positions.c. Caution: Drivers must ensure proper ramp setup, with minimal loading angles to avoid damage to vehicles

undercarriage and its components. Reduce vehicle-loading speeds when approaching or exiting skids as there isonly 2 ¾-inch (6.99 cm) distance between the front fascia and the pavement upon exiting skids.

d. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle securement isprohibited. Wheel straps must contact tire tread surfaces only. Soft-tie side pulls and strap contact withundercarriage components are strictly prohibited.

RAIL LOADING RAIL LOADING a. Tri-level railcars*: Approved for all loading positions, utilize low-profile chock systems. The use of the

6 inch (15.24 cm) SCT Copolymer and Holland Steel Tri-Lo’s or similar off-brand chock sets, are strictly prohibitedfor securing CN7’s with installed mudguards, on all tri-level railcar decks. Follow AAR policy for vehicle spacing, installing and removing securements. Install chocks firmly against vehicle tires.

b. AutoMax tri-level railcars: Approved conveyance, utilize low-profile chock systems. Load only (2) CN7’s onthe flatter surfaces of AutoMax ‘A’ decks. Vehicles with a higher undercarriage clearance (SUV) may also beplaced A3 and in A6 positions, if available. ‘B’ & ‘C’ decks, load four Elantra CN7’s on each deck, per railcar.Follow AAR policy for vehicle spacing, installing and removing securements. Install chocks firmly against tires.

c. Bi-level railcars: Bi-level railcars can be utilized in the event of a tri-level railcar shortage. The Elantra CN7 isapproved in all bi-level railcar-loading positions. Place chock setting in the highest setting that will maintain aminimum of 2” (5.08 cm) clearance between the chock and any vehicle component. Install chocks firmly againstvehicle tires.

GENERAL a. The Hyundai Elantra Sedan has a limited ground clearance of approximately 6 in. (15.24 cm).

Caution: Lower front fascia damage can occur when entering or exiting steep ramp angles at speeds in excess of 2.5 mph.

b. Always wear a seatbelt when operating vehicle. c. The Elantra must be shipped with its front tires in the straight forward position, automatic transmission placed in “Park” or in ‘first gear’ for manual transmission and its parking brake fully engaged.

d. Key placement: cup holder. *Includes all standard, Auto-Flex and Multi-Max railcars.

X

HCN72007R1 July 17, 2020

2021 CN7

MY2021 Hyundai Elantra Sedan

Specifications MY 2021 Hyundai Elantra (CN7)Models: SE, SEL & Limited N Line2.0L MPI DOHC 16V 1.6 Turbo GDI DOHC 16V147hp @ 6,200 201hp @ 6,000

Wheelbase: 107.1"272.03cm 107.1"272.03cmLength: 184.7"469.14cm 184.7"469.14cmHeight: 55.7' 141.48cm 55.7' 141.48cmWidth: 71.9" 182..63cm 71.9" 182..63cmTires/wheels: 15", 16", 17" - 38.10, 40.64, 43.18cmTires/wheels: N Serie18" 45.72cm 18" 45.72cmMin. Ground Cle5.3" 13.46cm 5.5" 13.97cmCurb weights: 2,725 - 3,990 lbs. 1236.04 - 1,809.83 kg

* Subject to change without notice

Technical BulletinNUMBER: DATE:

HYUNDAI KIA MODEL YEAR: MODEL:

SUBJECT:

1.

17305 Von Karman, Suite 200 Irvine, CA 92614

QUALITY 714-435-2990

COMMENTS:

TRUCK HAULAWAY a. Upper deck: Approved for all upper deck positions. Avoid using wheel pocket extensions in the

head rack position due to insufficient undercarriage clearance.b. Lower deck: Approved for all lower deck positions. Use caution over the trailer’s tandem wheels

and ramp break-over points due to reduced undercarriage clearance.c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle

securement is strictly prohibited. Wheel straps may contact tire tread surfaces only. Soft-tie sidepulls or strap contact with undercarriage or suspension components is strictly prohibited.

d. Caution: Reduce vehicle loading speeds when approaching or exiting skids, trailer tandems andramp break-over points.

RAIL LOADINGa. Tri-level railcars*: The Elantra GT and the GT N Line models are approved for standard tri-level

railcar shipments. The use of SCT Copolymer and Holland steel Tri-Lo’s or similar off-brandchock sets on tri-level railcars are strictly prohibited.

b. Bi-level rail cars: May be utilized in the event of a tri-level railcar shortage. The Hyundai ElantraGT and GT N Line is approved in all bi-level loading positions. Place chock setting in the highestsetting that will maintain a minimum of 2 in. (5.08 cm) clearance between the chock and anyvehicle component. Install chocks firmly against tires.

GENERAL

a. The Elantra GT and GT N Line have a limited ground clearance of approximately 5.1 in. (12.95 cm).b. Always wear a seatbelt when operating vehicle.c. Both the GT and GT N Line must be shipped with its front tires in the straight forward position.

Place automatic transmissions in “Park” or in ‘first gear’ for manual transmissions, and ensure itsparking brake fully engaged.

* Includes all Standard, AutoMax, Auto-Flex and Multi-Max railcars. Copolymer chock sets may not be used.

hp @ 6,000 rpm

. DCT (1,431.08 kg) Max.

264.92 cm)

09 cm)

X

HPD1703R3 03 Mar 2017

2019 - 2020 PD

MY2019 – MY2020 Hyundai Elantra GT and GT N Line

All weights and dimensions are approximate and are subject to change.

Specifications

GT N Line

2.0L 4 D-CVTT 161hp @ 6,200 rpm 1.6L Turbo DOCH 201hp @ 6,000 rpm

Curb Weight: 3,040 lbs. (1,378.92 kg) Curb Weight: 3,155 lbs. DCT (1,431.08 kg) Max.

Wheelbase: 104.3 in. (264.92 cm) Wheelbase: 104.3 in. (264.92 cm)

Length: 170.9 in. (434.09 cm) Length: 170.9 in. (434.09 cm)

Width: 70.7 in. (179.58 cm) Width: 70.7 in. (179.58 cm)

Height: 57.7 in. (146.56 cm) Height: 57.7 in. (146.56 cm)

Wheels: 17 in. (43.18 cm) Wheels: 18 in. Alloy (45.72 cm)

Page 1 of 1Revision R3

Technical BulletinNUMBER: TEST DATE:

HYUNDAI KIA MODEL YEAR: MODEL CODE:

SUBJECT:

COMMENTS:

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY 714-435-2960

Page 1 of Revision

IONIQ Specifications Hybrid models: Blue, SE, SEL & Limited

Hybrid: DOHC 1.6L GDI 4 cylinder 43 hp (32 kW) Est. 139 hp combined Plug-In: 60 hp (45 kWh) 60 hp combined 139 hp (88kW) Electric: 100kw 134 hp.

Curb weight: Hybrid 3,115 lbs. Plug-In 3,417 lbs. Elec 3,488 lbs. (1,412.94-1,582.13kg)

Wheelbase: 106.3 in. (270 cm) Length: 176.0 in. (447.04 cm)Width: 71.7 in. (182.12 cm) Height: 56.9 in. (144.53 cm)

Wheels: 15 in., 17 in. or 18 in. Alloy (38.10, 43.18 or 45.72 cm) Automatic Trans*All weights and dimensions are subject to change without notice

HAE1611R6 11/09/2016

2021 AE

MY2021 Hyundai IONIQ Hybrid [HEV, EV & PHEV]

TRUCK HAUL-AWAYa. Upper Deck: Approved for all upper deck positions.b. Lower deck: Approved for all lower trailer positions. Use caution over tandem wheel area.c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of

securement are prohibited. Wheel straps may contact tire tread surfaces only. Side pullsand strap contact with undercarriage components are strictly prohibited.

RAIL LOADINGa. Standard tri-level and AutoFlex railcars: Approved for all deck levels. IONIQ’s must be

secured away from any end door to provide necessary 3“ (7.62 cm) roof clearance. SCTCopolymers chocks are prohibited on all IONIQ models for tri-level railcar securement. Allother chock sets may be utilized provided they maintain a minimum 2” (5.08 cm) clearancebetween chock and vehicle body panels or components.

b. AutoMax rail cars: Not an approved conveyance as many utilize SCT Copolymer chocks.c. Bi-level rail cars: Approved for all deck levels and loading positions. Grate lock chocks

may be utilized provided chocks are set at the highest setting that will maintain a minimumof 2” (5.08 cm) clearance between chock and any vehicle body panels or components.

GENERALa. The Hyundai IONIQ has approximately 5.3 inches (13.46 cm) of ground clearance.b. EV and PHEV (Plug-in) recharging is restricted to trained personnel only. High voltage

cables and connectors are orange in color. Do not touch high voltage components, cables orconnections without proper protective gear. Failure to observe this warning could result inelectrical shock, injury or even death.

c. ‘No start’ hybrid or electric vehicles: please contact the GLOVIS Claims Department fordirections at 1-866-445-6847. Always wear a seatbelt when operating vehicle.

d. EV and PHEV battery charging kit responsibility follows the carrier chain of custody rules.e. Vehicle must be shipped with its front tires in the straight forward position, the

transmission in “Park” position and its parking brake fully engaged.

1R6

X

Technical Bulletin NUMBER: DATE:

HYUNDAI KIA MODEL YEAR: MODEL:

SUBJECT:

1.

17305 Von Karman, Suite 200 Irvine, CA 92614

QUALITY 714-435-2990

Rev. 04 Page 1 of 1

COMMENTS:

TRUCK HAULAWAY

a. Upper deck: Approved for all upper deck positions. b. Lower deck: Approved for all lower deck positions. c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle securement

is strictly prohibited. Wheel straps may contact tire tread surfaces only. Strap side pulls or strap contact with undercarriage or suspension components is strictly prohibited.

d. Drivers ensure proper ramp setup with minimal loading angles over tandems and break-over points to avoid damage to vehicle undercarriage components.

RAIL LOADING

a. Standard and AutoMax tri-level railcars: Hyundai Veloster 2.0, R-Spec, Turbo series vehicles are approved for all deck levels. Always approach railcar entrances with caution, as older tri-level railcars have varying height and deck limitations. Railcar ‘A’ decks: secure and ship all Veloster models on flat surfaces only, never on deck inclines. Follow AAR policy for installing, spacing, and removing chocks. Install chocks firmly against vehicle tires. Use Low-profile chock sets whenever possible. Low-profile chocks are required whenever mudguards or ground effects packages are installed. b. Bi-level rail cars: Approved for all deck levels and loading positions. Grate/Grip lock type chocks are typically set: front chocks - low setting, rear chocks - high setting. Follow AAR policy whenever installing, spacing, and removing chocks. Install chocks firmly against tires. c. Autoflex and Multi-Max railcars may be utilized in either the bi-level or tri-level configuration. Follow the above tri-level or bi-level guideline based on railcar configuration.

GENERAL

• The 2021 Hyundai Veloster, R-Spec, Turbo series vehicles have approximately 5.6 in. (14.22 cm) of ground clearance. Caution: Lower front fascia damage can occur when entering or exiting steep ramp angles at speeds in excess 2.5 mph. • Always wear a seatbelt when operating vehicle. • Veloster’s must be shipped with its front tires in the straightforward position, the transmission placed in the “Park” position and its parking brake fully engaged.

X

HJS1803R4 07/25/2018

2021 JS

MY2021 Hyundai Veloster [2.0, R-Spec, Turbo]

2021 Hyundai Veloster Specifications: Engine sizes: NU 2.0, Gamma 1.6T & Theta 2.0T

Curb weight: Man. 2,701 lbs. – Auto. 2,987 lbs. (1,225.15 – 1,354.88 kg) Wheelbase: 104.3 in. / 264.92 cm

Length: 166.9 in. / 423.93 cm Width: 70.9 in. / 180.09 cm Height: 55.1 in. / 139.95 cm

17, 18 or 19 in. Alloy (43.18 cm, 45.72 cm, or 48.26 cm)

All weights and dimensions are approximate and are subject to change.

Technical BulletinNUMBER: DATE:

HYUNDAI KIA MODEL YEAR: MODEL:

SUBJECT:

1.

17305 Von Karman, Suite 200 Irvine, CA 92614

QUALITY 714-435-2990

Page 1 of 1 Revision 2

COMMENTS: TRUCK HAULAWAY

Upper trailer deck: MY2021 Hyundai Sonata DN8 approved for all upper deck positions. a. Upper deck restriction: regardless of the tractor or trailer’s manufacturer or the trailer’s length, the Hyundai Sonata DN8 may

only be loaded facing the forward direction in the trailer’s #1 headrack position. Close or use a high pocket position in thetrailer’s headrack to prevent front fascia or suspension damage.

Lower trailer deck: Lower deck restriction: Lower trailer, tandem wheel area. a. Use extreme caution loading over the trailer’s lower deck tandem pivot area. The Sonata DN8 may only be loaded facing backwards

on bottom deck, in the first three lower deck vehicle positions. Should your trailer’s lower deck equipment not handle a Sonataloaded backwards, contact your dispatch office for a replacement vehicle that will have a higher clearance/profile needed forthat position.

b. Reduce loading speeds when backing the Sonata onto trailer skids and tandem area. Vehicle has 5.3 in. (13.46 cm) ofground clearance and 111.8” (283.97 cm) wheelbase. The vehicle’s rocker panel over tandem area of trailer can drop to lessthan 1” (5.08 cm) of deck clearance.

c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle securement other than soft-ties is strictly prohibited. Wheel straps may contact tire tread surfaces only. Side pulls or strap contact with undercarriagecomponents is also prohibited.

RAIL LOADING

Standard Tri-level railcars: a. Standard tri-level and AutoMax railcars ‘A’, ‘B’ and ‘C’ deck loading positions are approved conveyances for the

Sonata DN8. Utilize railcars with low profile chocking systems, whenever possible.b. Install all chocks firmly against vehicle tires.c. Maintain a min. of 2” (5.08 cm) clearance between the chock and any vehicle body panel and its components. Follow

AAR policy for vehicle spacing, installing and removing securements. Install chocks firmly against vehicle tires. AutoMax tri-level railcars: a. AutoMax railcars are an approved conveyance. Load only (2) DN8’s on flat surfaces of AutoMax ‘A’ decks and a vehicle with higher

undercarriage clearance (SUV, etc.) in A3 and in A6 positions, if available. Utilize railcars with low profile chocking systemswhenever possible. ‘B’ & ‘C’ decks, may load four units on each deck, per railcar. Follow AAR policy for vehicle spacing, installingand removing of securements. Install chocks firmly against vehicle tires.

Bi-level railcars: a. Bi-levels railcars are an approved conveyance, should tri-level railcars become unavailable due to a tri-level railcar shortage.b. Sonata DN8’s are approved in all bi-level railcar-loading positions. Follow AAR policy for vehicle spacing, installing and

removing of securements. Install chocks firmly against vehicle tires.

GENERAL a. The 2021 Sonata has approximately 5.3 in. (13.46 cm) of ground clearance.b. Ship the Sonata DN8 sedan with its front tires in the straightforward position, the transmission in “Park” position and parking

brake fully engaged.c. Key/FOB placement: Cup holder.

X

HDN81910R2 10/04/2019

2021 DN8

MY2021 Hyundai Sonata Sedan

2021 Sonata Specifications SE, SEL 2.5 L I4 GDI SEL Plus, Limited 1.6 Turbo I4 Curb Wt: 3,120 – 3,266 lbs. (1,415-1,481kg) 3,230 - 3,336 lbs. (1,465-1,513kg) Wheelbase: 111.8 in. (283.97cm) 111.8 in. (283.97cm) Length: 192.9 in. (489.97cm) 192.9 in. (489.97cm) Width: 73.2 in. (185.93cm) 73.2 in. (185.93cm) Height: 56.9 in. (144.53cm) 56.9 in. (144.53cm) Min ground clearance: 5.3 in (13.46cm) 5.3 in. (13.46cm)

Wheels: 16, 17, 18 or 19 in. (40.64, 43.18, 45.72 or 48.26cm) Specifications subject to change without notice.

Technical BulletinNUMBER: DATE:

HYUNDAI KIA MODEL YEAR: MODEL:

SUBJECT:

1.

17305 Von Karman, Suite 200 Irvine, CA 92614

QUALITY 714-435-2990

Page 1 of 1 Revision 0

COMMENTS: TRUCK HAULAWAY Upper trailer deck: MY2021 Hyundai Sonata DN8 Hybrid is approved for all upper deck positions. a. Upper deck restriction: regardless of the tractor or trailer’s manufacturer or the trailer’s length, the Hyundai Sonata DN8 HEV may only be

loaded facing the forward direction in the trailer’s #1 headrack position. Close or use a high pocket position in the trailer’s headrack toprevent front fascia or suspension damage.

Lower trailer deck: Lower deck restriction: Lower trailer, tandem wheel area. a. Use extreme caution loading over the trailer’s lower deck tandem pivot area. The Sonata DN8 HEV may only be loaded facing backwards on bottom

deck, in the first three lower deck vehicle positions. Should your trailer’s lower deck equipment not handle a Sonata loaded backwards, contactyour dispatch office for a replacement vehicle that will have a higher clearance/profile needed for that position.

b. Reduce loading speeds when backing the Sonata onto trailer skids and tandem area. Vehicle has 5.3 in. (13.46 cm) of ground clearance and 111.8” (283.97 cm) wheelbase. The vehicle’s rocker panel over tandem area of trailer can drop to less than 1” (5.08 cm) of deck clearance.

c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle securement other than soft-ties is strictlyprohibited. Wheel straps may contact tire tread surfaces only. Side pulls or strap contact with undercarriage components is also prohibited.

RAIL LOADING

Standard Tri-level railcars: a. Standard tri-level and AutoMax railcars ‘A’, ‘B’ and ‘C’ deck loading positions are approved conveyances for the Sonata DN8 HEV. Utilize

railcars with low profile chocking systems, whenever possible. b. Install all chocks firmly against vehicle tires. c. Maintain a min. of 2” (5.08 cm) clearance between the chock and any vehicle body panel and its components. Follow AAR policy for vehicle

spacing, installing and removing securements. Install chocks firmly against vehicle tires.AutoMax tri-level railcars: a. AutoMax railcars are an approved conveyance. Load only (2) DN8’s on flat surfaces of AutoMax ‘A’ decks and a vehicle with higher

undercarriage clearance (SUV, etc.) in A3 and in A6 positions, if available. Utilize railcars with low profile chocking systems whenever possible.b. ‘B’ & ‘C’ decks, may load four units on each deck, per railcar. Maintain a min. of 2” (5.08 cm) clearance between the chock and any vehicle

body panel and its components. Follow AAR policy for vehicle spacing, installing and removing of securements. Install chocks firmly against vehicle tires.

Bi-level railcars: a. Bi-levels railcars are an approved conveyance, should tri-level railcars become unavailable due to a tri-level railcar shortage.b. Sonata DN8’s are approved in all bi-level railcar-loading positions. Follow AAR policy for vehicle spacing, installing and removing of

securements. Install chocks firmly against vehicle tires.

GENERAL a. The 2021 Sonata has approximately 5.3 in. (13.46 cm) of ground clearance.b. EV recharging is restricted to trained personnel only. High voltage cables and connectors are orange in color. Do not touch high voltage

components, cables or connections without proper protective gear. Failure to observe this warning could result in electrical shock, injury oreven death. No start hybrid or electric vehicles, please contact the GLOVIS Claims Department for directions at 1-866-445-6847.

c. Ship the Sonata DN8 Hybrid Sedan with its front tires in the straightforward position, the transmission in “Park” position and parking brake fully engaged.

d. Key placement: Cup holder. Specifications

Hybrid Blue, SEL & Limited HEV 2.0L I4 Hybrid DOHC

39kW (51 HP) @ 1,800 - 2,300 rpm - Combined 192 HP Max. Curb Wt.: 3,530 lbs. (1,601.18kg)

Wheelbase: 111.8 in (283.97cm) Length: 192.9 in (489.97cm)

Width - excludes mirrors: 73.2 in (185.93cm) Height: 56.9 in (144.53cm)

Wheels: 16 or 17 in. (40.64, 43.18 cm) Min. Ground Clearance: 5.3 in (13.46cm)

Transmission: AT *All weights and dimensions are subject to change without notice.

X

HDN81910R0 10/04/2019

2021 DN8 HEV

MY2021 Hyundai Sonata Hybrid

1.

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY714-435-2990

Page 1 of 1Revision 3

Technical BulletinNUMBER:

HOS1710R1DATE:

07/25/2018HYUNDAI

XKIA MODEL YEAR:

2021MODEL:

OS and OSEV

SUBJECT:MY2021 Hyundai Kona and Kona Electric CUV

HOS1710R3

COMMENTS:TRUCK HAULAWAY

a. Upper deck: Approved - all upper deck positions.b. Lower deck: Approved - all lower deck positions.c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle securement is

strictly prohibited. Wheel straps may contact tire tread surfaces only. Strap side pulls or strap contact withundercarriage components is strictly prohibited.

RAIL LOADINGa. Bi-level rail cars: Approved for all deck levels and loading positions. Grate lock chocks should be placed

in the highest setting that will maintain a minimum of 2”(5.1 cm) clearance between the chock body andany vehicle component. Follow AAR policy for installing, spacing and removing chocks. Install chocksfirmly against tires.

b. Standard tri-level rail cars*: Kona OS and Kona Electric OS EV are approved for shipment on ‘C’ deck ofstandard tri-level equipment only. Always approach older railcar entrances with caution, as they can havevarying height limitations. Follow AAR policy for installing, spacing and removing chocks.Install chocks firmly against tires.

c. AutoMax rail cars: Hyundai Kona’s are approved for all deck levels. A smaller vehicle like a HyundaiAccent may be may be shipped behind 2 Kona’s on ‘A’ deck on railcar #1, and with a similar configurationfor railcar #2. Follow AAR policy for installing, spacing and removing chocks. Install chocks firmly againsttires.

a. Autoflex and Multi-Max railcars may be utilized provided they are set to bi-level configuration only.GENERAL

a. The 2021 Kona has approximately 6.7 inches (17.0 cm) and EV 6.2 inches (15.75 cm) EV of ground clearance.b. The Kona must be shipped with its front tires in the straight forward position, the transmission in thec. “Park” position and its parking brake fully engaged.d. Electric vehicle recharging is restricted to trained personnel only. High voltage cables and connectors are

orange in color. Do not touch high voltage components, cables or connections without proper protectivegear. Failure to observe this warning could result in electrical shock, injury or even death.

e. Always wear a seatbelt when operating the vehicle.f. No start hybrid or electric vehicles, please contact the GLOVIS Claims department for directions at

1-866-445-6847.. 2021 Hyundai Kona SpecificationsDOHC 2.0L I4 - 6 speed auto/ 1.6L I4 Turbo/ 150kW EV 201 hp @ 3,600 rpm

Curb weights: 2.0L FWD 2,899 lbs. (1,314.96kg), 2.0L AWD 3,126 lbs.(1,417.93kg) Curb weights: 1.6T FWD: 3,062 lbs.(1,388.90kg) -1.6T AWD 3,276 lbs.(1,485.97kg)

Curb weights: EV SEL 3,715 lbs.(1,685.10kg), EV Limited 3,770 lbs.(1,710.04kg), EV Ultimate 3,836 lbs.(1,739.98kg)Wheelbase: 102.4 in. / 260.1 cm

Length: 164.0 in. / 416.6 cmWidth: 70.9 in. / 180.1 cm

Height: 61.0 in. / 61.6 in. (with rails) / 154.9 cm – 155.2 cm with rails.16, 17 & 18 in. Alloy 40.6, 43.2, 45.7 cm

All weights and dimensions are approximate and are subject to change.

1.

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY714-435-2990

Page 1 of 1Revision 4

Technical BulletinNUMBER:

HOS1710R1DATE:

03/30/2018

HYUNDAI

XKIA MODEL YEAR:

2021MODEL:

FE

SUBJECT:MY2021 Hyundai NEXO Hydrogen Fuel Cell [FCEV]

HFE1804R4

COMMENTS:TRUCK HAULAWAY

a. Upper deck: Approved - all upper trailer deck positions only.b. Lower deck: NEXO FCEV may not be loaded on haulaway trailer lower trailer decks. No exceptions.c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle securement is

strictly prohibited. Wheel straps may contact tire tread surfaces only. Wheel strap side pulls and /orstrap contact with undercarriage components is strictly prohibited.

RAIL LOADINGa. Bi-level rail cars: Approved for bi-level railcar shipments.b. Grate lock chocks should be placed in the highest chock setting that will maintain a minimum of

2”clearance between the chock body and any vehicle components. Follow AAR policy for installing,spacing and removing chocks. Install chocks firmly against tires.

c. Standard tri-level rail cars: Not an approved conveyance.d. AutoMax rail cars: Hyundai NEXO’s are approved for AutoMax railcars - all deck levels. No

known chock type restrictions. Maintain a minimum of 3” deck to vehicle roof clearance in all load positions. Load on AutoMax: A deck: 3 vehicles, B deck: 4 vehicles, C deck: 4 vehicles. Follow AAR policy for installing, spacing and removing chocks. Install chocks firmly against tires.

e. Autoflex and Multi-Max railcars may be utilized provided they are set to bi-level configuration only.Install chocks firmly against tires.

GENERALa. The 2021 Hyundai NEXO has approximately 6.4 inches (16.26 cm) of ground clearance.b. The Nexo must be shipped with its front tires in the straight forward position, the transmission in the

“Park” position and its parking brake fully engaged.c. EV recharging is restricted to trained personnel only. High voltage cables and connectors are orange in

color. Do not touch high voltage components, cables or connections without proper protective gear.Failure to observe this warning could result in electrical shock, injury or even death.

d. Always wear a seatbelt when operating vehicle.e. No start hybrid or electric vehicles, please contact the GLOVIS Claims department for directions.f. Key placement: Cup holder. Specifications

2021 Hyundai NEXO FE Fuel Cell Model: Blue & LimitedHydrogen Fuel Cell 135kW (95 stack + 40kW battery)

Output: 120kW / (161 HP) Weelbase: 109.8 in. /278.9 cm) Curb weight: Blue: 3,990 lbs. (1,810 kg) Limited: 4,116 lbs. (1,867 kg)

Length: 183.9 in. / 467.1 cm Width: 73.2 in. excl. mirrors / 185.9 cm Height: 64.2 in./64.6 in. (with rails) / 163.1 cm / 164.1 cm

17 in. & 19 in. Alloy / 43.2 cm & 48.3 cm Minimum ground clearance 6.4 in / 16.26 cm All weights and dimensions are approximate and subject to change.

1.

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY714-435-2990

Page 1 of 1Revision 4

Technical BulletinNUMBER:

HOS1710R1TEST DATE:

03/27/2015HYUNDAI

XKIA MODEL YEAR:

2021MODEL CODE:

TL

SUBJECT: MY2021 Hyundai Tucson CUV

HTL1906R4

COMMENTS:

TRUCK HAULAWAY

a. Upper / Lower decks: Approved all loading positions – No restrictions.

b. Upper deck: Always check vehicle load heights for compliance with U.S. FMCSA 13’.6“ or State 14’ height load height limitations where applicable.

c. Lower decks: Carriers always maintain a minimum of 4” (10.16 cm) space separation between upper and lower deck vehicles. Use caution when loading directly behind the driver’s cab on trailers built with short ramps seen on many 65’ trailers, and trailers with limited overhead clearances.

d. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle securement is strictly prohibited. Wheel straps may contact tire tread surfaces only. Strap side pulls

or strap contact with undercarriage components is strictly prohibited.

RAIL LOADING

a. Bi-level railcars: The Hyundai Tucson is approved for bi-level railcar shipment only. Utilize the highest chock setting that will maintain a minimum of 2” (5.08 cm) clearance between the chock body and any vehicle component. Follow AAR policy for installing, spacing and removing securements. Install chocks firmly against tires.

b. Standard tri-level railcars: Not an approved conveyance. c. AutoMax: Not rated. Not an approved conveyance.

GENERAL

a. The Hyundai Tucson CUV has approximately 6.4 inches (16.26 cm) of ground clearance.b. The Tucson must be shipped with its front tires in the straightforward position, the transmission in the

“Park” position and its parking brake fully engaged.c. Always wear a seatbelt when operating vehicle.d. Key placement: Cup holder.

.

2021 Hyundai Tucson Specifications

Models: SE, Value, SEL, Sport, Limited, and Ultimate

SE & Value: DOHC 2.0L I4 - 6 speed auto / All others: DOCH 2.4L I4 - 6 speed auto

Curb weights: 3,309 lbs. - 3,732 lbs. (1,500.94 kg – 1,692.81 kg)

Wheelbase: 105.1 in. / 266.95 cmLength: 176.4 in. / 448.06 cm

Width: 72.8 in. / 184.91 cm

Height: 64.8 in. / 65.0 in. (with rails) / 164.59 – 165.10 cm

Wheels: 17, 18 & 19 in. Alloy

43.18 cm, 45.72 cm, 48.26 cm

*All weights and dimensions are approximate and are subject to change

1.

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY714-435-2990

Page 1 of 1Revision 1

Technical BulletinNUMBER:

HOS1710R1TEST DATE:

02/25/2021HYUNDAI

XKIA MODEL YEAR:

2022MODEL CODE:

NX4

SUBJECT: MY2022 Hyundai Tucson CUV

HNX42102R1

COMMENTS:

TRUCK HAULAWAYa. Upper deck: MY2022 Hyundai Tucson may not be loaded in the #1 head rack position. All other upper

deck positions are approved, provided vehicle height does not exceed U.S. Federal 13’.6” or State load height limitations. Please load the Hyundai Tucson facing the forward direction in all other upper trailer positions including position 2, 3, 4 and 5 whenever possible. Always check vehicle load heights for compliance with U.S. FMCSA 13’.6“ or State 14’ height load height limitations where applicable.

b. Lower decks: Carriers always maintain a minimum of 4” (10.16 cm) space separation between upper and lower deck vehicles. Use caution when loading directly behind the driver’s cab on trailers built with short ramps seen on many 65’ trailers, and trailers with limited overhead clearances.

c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle securement is strictly prohibited. Wheel straps may contact tire tread surfaces only. Strap side pullsor strap contact with undercarriage components is strictly prohibited.

RAIL LOADINGa. Bi-level railcars: The Hyundai Tucson is approved for bi-level railcar shipment only. Utilize the

highest chock setting that will maintain a minimum of 2” (5.08 cm) clearance between the chock body and any vehicle component. Follow AAR policy for installing, spacing and removing securements. Install chocks firmly against tires.

b. Standard tri-level railcars: Not an approved conveyance. c. AutoMax: Not rated. Not an approved conveyance.

GENERALa. The 2022 Tucson NX4 has approximately 7.1 in. (2WD) and 8.3 in. (AWD) ground clearance.b. The Tucson must be shipped with its front tires in the straightforward position, the transmission in the

“Park” position and with its parking brake fully engaged.c. Always wear a seatbelt when operating vehicle. d. Key placement: Cup holder.

.

BI-LEVEL LOAD

FACTOR

A D

ECK

B DECK

Vehicles 5 5

TRUCK LOAD

FACTOR

TOP D

ECK

BOTTO

M D

ECK

Vehicles 4 4

Specifications: MY2022 Hyundai Tucson NX4

2.5L I4 Smartstream GDI MPI 1.6L I4 Turbo Hybrid HEV (Weights for PHEV SEL & Limited TBD)

Est. Max. Curb weight: I4 2.5 2.5L 3,651 lbs. (1,656.07 kg) Est. Max. Curb weights: I4 T 3,752 lbs. (1,701.88 kg) Length: 182.3 in. (463.04 cm) Width: 73.4 in. (186.44 cm)

Height 65.6 in. with roof rails (166.62 cm) Wheels: 17 & 19 in. Alloy (43.18, 48.26 cm)

Transmission: Automatic *All weights and dimensions are subject to change without notice

Technical Bulletin NUMBER: DATE:

HYUNDAI KIA MODEL YEAR: MODEL:

SUBJECT:

1.

17305 Von Karman, Suite 200 Irvine, CA 92614

QUALITY 714-435-2990

Page 1 of 1 Revision 4

COMMENTS:

TRUCK HAULAWAY a. Upper decks: No Restrictions. All other upper deck positions are approved, provided vehicle height

does not exceed U.S. Federal 13’.6” or State 14’ load height limitations. Please load Santa Fe’s facing the forward direction in all upper trailer positions #1 through #5 if possible, provided that doing so does not affect carrier vehicle load capacity.

b. Lower decks: Always maintain a minimum of 4” (10.16 cm) space separation between upper and lower decks and vehicles. Use caution: when loading the Santa Fe in position #6, not all trailer configurations can accommodate the Santa Fe’s size or trailers having limited overhead clearances.

c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle securement except soft-tie tire straps is strictly prohibited. Wheel straps may contact tire tread surfaces only. Side pulls or strap contact with undercarriage components is strictly prohibited.

RAIL LOADING a. Bi-level railcars: Bi-level railcars are the Santa Fe’s primary conveyance, approved for all deck positions. Utilize the highest chock setting that will maintain a minimum 2” (5.08 cm)

clearances between the chock and any vehicle component. Holden Grate Lock chocks® set the front chock face plates at medium setting, high setting for rear chocks. All other chock systems follow AAR loading and spacing guidelines. Place chocks firmly against tires.

b. Tri-level railcars: Standard tri-level railcars are not an approved conveyance. c. AutoMax railcars: Approved for AutoMax railcar shipment. AutoMax ‘A’ decks: maximum of

‘2’ Santa Fe vehicle capacity. Ship Hyundai Santa Fe’s on flat railcar surfaces only, never on ‘A’ deck inclines. Load AutoMax ‘A’ decks: 2 Santa Fe’s, ‘B’ deck: 4 vehicles, ‘C’ deck: 4 vehicles. Use caution when entering or exiting ‘B’ decks with installed roof rack rails. Always follow AAR loading and spacing guidelines.

GENERAL a. The 2021 Hyundai Santa Fe has an estimated 8.2 in. (20.83 cm) ground clearance. b. The Santa Fe must be shipped with its front tires in the straightforward position, the transmission in “Park” position and parking brake fully engaged. c. Always wear a seatbelt when operating vehicle. d. Key placement: Cup holder.

X

HTM1808R4 03/30/2018

2021 TM

MY2021 Hyundai Santa Fe SUV

2021 Santa Fe Specifications Models: SE and SEL 2.5L I4 MPI DOHC GDI 16-v TBD Est. Curb weight: 3,600 ~ 3,975 lbs. (1,808.03 kg) Wheelbase: 108.9 in. (277 cm) Length: 188.4 (478.54 cm) Width: 74.8 in. (189.99 cm) Height: 67.3 (w/rails) 170.94 cm Wheels: 17” or 18“Alloy (43 cm/46 cm) Transmission: automatic

All weights and dimensions are approximate and are subject to change.

2021 Santa Fe Specifications Models: Limited and Calligraphy 2.5L Turbo I4 DOHC GDI 16-v TBD Est. Curb weight: 4,000 ~ 4,175 lbs. (1,893.75 kg) Wheelbase: 108.9 in. (277 cm) Length: 188.4 (478.54 cm) Width: 74.8 in. (189.99 cm) Height: 67.3 (w/rails) 170.94 cm Wheels: 18”, 19” or 20” Alloy (46 cm/48 cm/51 cm) Transmission: automatic

Technical Bulletin NUMBER: DATE:

HYUNDAI KIA MODEL YEAR: MODEL:

SUBJECT:

1.

17305 Von Karman, Suite 200 Irvine, CA 92614

QUALITY 714-435-2990

Page 1 of 1 Revision

COMMENTS: TRUCK HAULAWAY a. Upper decks: No Restrictions. All other upper deck positions are approved, provided vehicle height does

not exceed U.S. Federal 13’.6” or State 14’ load height limitations. Please load Santa Fe’s facing the forward direction in all upper trailer positions 1 through 5 if possible, providing doing so does not affect carrier vehicle load capacity.

b. Lower decks: Always maintain a minimum of 4” (10.16 cm) space separation between upper and lower decks and vehicles. Use caution: when loading the Santa Fe in position #6, not all trailer configurations can accommodate the Santa Fe’s size or trailers having limited overhead clearances.

c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method of vehicle securement except soft-tie tire straps is strictly prohibited. Wheel straps may contact tire tread surfaces only. Side pulls or strap contact with undercarriage components is strictly prohibited.

RAIL LOADING a. Bi-level railcars: Bi-level railcars are the Santa Fe’s primary conveyance, approved for all deck positions.

Utilize the highest chock setting that will maintain a minimum 2” (5.08 cm) clearances between the chock and any vehicle component. Holden Grate Lock chocks® set the front chock face plates at medium setting and following AAR loading and spacing guidelines.

b. Tri-level railcars: Standard tri-level railcars are not an approved conveyance. c. AutoMax railcars: Approved for AutoMax railcar shipment. AutoMax ‘A’ decks: maximum of ‘2’

Santa Fe vehicle capacity. Ship Santa Fe’s on flat railcar surfaces only, never on ‘A’ deck inclines. Load AutoMax ‘A’ decks: 2 Santa Fe’s, ‘B’ deck: 4 vehicles, ‘C’ deck: 4 vehicles. Use caution when entering or exiting ‘B’ decks with installed roof rack rails. Always follow AAR loading and spacing guidelines.

GENERAL a. The 2021 Hyundai Santa Fe has an estimated 8.2 in. (20.83 cm) of ground clearance. b. EV recharging is restricted to trained personnel only. High voltage cables and connectors are orange in

color. Do not touch high voltage components, cables, or connections without proper protective gear. Failure to observe this warning could result in electrical shock, injury or even death. No start hybrid or electric vehicles, please contact the GLOVIS Claims Department for directions at 1-866-445-6847.

c. The Santa Fe must be shipped with its front tires in the straightforward position, the transmission in “Park” position and parking brake fully engaged.

d. Always wear a seatbelt when operating vehicle. e. Key placement: Cup holder.

X

HTMHEV18R0 03/30/2018

2021 TM HEV

MY2021 Hyundai Santa Fe HEV

All weights and dimensions are approximate and are subject to change.

Specifications 2021 Santa Fe SEL HEV & LIMITED HEV 1.6L Turbo I4 DOHC GDI 16-v, 44.2 kW (est. 59 HP) @ 1,600 rpm Curb weight: 4,204 lbs. (1,906.90 kg) Wheelbase: 108.9 in. (277 cm) Length: 188.4 in. (478.54 cm) Width: 74.8 in. (189.99 cm) Height: 67.3 in. (w/rails) (170.94 cm) Wheels: 18 in Alloy (45.72 cm) Transmission: automatic

Technical BulletinNUMBER: TEST DATE:

HYUNDAI KIA MODEL YEAR: MODEL CODE:

SUBJECT:

COMMENTS:

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY 714-435-2960

Page 1 of Revision

HLX21902R5 02/15/2019

2021 LX2

MY2021 Hyundai Palisade SUV

TRUCK HAULAWAYa. Upper Deck: Palisade may not be loaded in the #1 head rack position. Installed

luggage rack adds 4.5” (11.43cm) to vehicle height and will exceed U.S. and Statemaximum load height limitations. All other upper deck positions are approved,provided vehicle height does not exceed U.S. Federal 13’.6” or State load heightlimitations. Please load Palisades facing the forward direction in all upper trailerpositions 2, 3, 4 and 5 whenever possible.

a. Lower deck: Approved for all lower trailer positions, except directly behind the driver’scab on trailers built with short ramps seen on many 65’ trailers, and trailers with limitedoverhead clearances. Carriers must maintain a minimum of 4” (10.16cm) overhead deckspace separation between upper and lower vehicles.

c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other methodof securement are strictly prohibited. Wheel straps may contact tire tread surfaces only.Side pulls and strap contact with undercarriage components are strictly prohibited.

RAIL LOADINGa. Tri-level railcars: Not Approved.b. Bi-level railcars: Approved for bi-level railcar shipments only. Utilize the highest chock

setting that will maintain a minimum of 2” (5.08cm) clearance between the chock andany vehicle body panel or its components. Follow AAR loading and spacing guidelines.Place chocks firmly against tires.

GENERALa. The Hyundai Palisade has approximately 7.9 inches (20cm) of ground clearance.b. Seat Belt(s) must be worn at all times. Key placement: cup holder.c. Vehicle must be shipped with its front tires in the straight forward position, the

transmission in “Park” position and its parking brake fully engaged.

1R5

X

Specifications Palisade models: SE, SEL, Limited, Calligraphy3.8L, GDI D-CVVT 24V 6 cylinder

Curb weight range: 7 passenger: 4,387 lbs. max. 8 passenger: 4,284 lbs. max. (1,989.91kg – 1,943.19kg)

Wheelbase: 114.2 in (290cm)Length: 196.1 in. (498cm)Width: 77.8 in. (198cm)Height: 68.9 in. (175cm)

Wheels: 20 in. Alloy standard (51cm)Transmission: Automatic

*All weights and dimensions are subject to change without notice

Technical BulletinTEST DATE:

HYUNDAI KIA MODEL CODE:

SUBJECT:

COMMENTS:

17305 Von Karman, Suite 200

Irvine, CA 92614QUALITY 714-435-2960

Page 1 of

Revision

NUMBER:

HQX1907R2 07/19/2019MODEL YEAR:

2021 QX

MY2021 Hyundai Venue SUV

TRUCK HAUL-AWAYa. Upper Deck: The Hyundai Venue SUV is approved for all trailer upper deck positions.

Always check vehicle load heights for compliance with U.S. FMCSA 13’.6“ or State 14’ loadheight limitations where applicable.

b. Lower deck: The Venue (QX) is approved for all lower trailer positions.Use caution: when loading the Venue in position #6 behind the driver’s cab, not all trailerconfigurations can accommodate the Venue’s size or on trailers having limited overheadclearances. Always maintain a minimum of 4” (10.16 cm) space separation between upperand lower vehicles.

c. Soft-tie wheel straps are required on all four (4) tires. Chains or any other method ofsecurement are strictly prohibited. Wheel straps may contact tire tread surfaces only. Sidepulls and strap contact with undercarriage components are strictly prohibited.

RAIL LOADINGa. Bi-level railcars: The Hyundai Venue is approved for bi-level railcar shipment. Loaders

utilize the highest chock setting that will maintain a minimum of 2” (5.08 cm) clearancebetween the chock and any vehicle body panel or its components.

b. Tri-level railcars: Standard tri-level railcars are not an approved conveyance.c. AutoMax railcars: Approved for AutoMax railcar shipment. Venue SUV restriction: AutoMax

‘A’ deck is limited to ‘2’ Venue QX’s on flat surfaces only. A smaller vehicle may be shippedbehind the 2 QX’s in the ‘A3’ and ‘A6’ ramp positions, provided that the smaller unit ispermitted to utilize SCT Copolymer chock sets. Always maintain a minimum of 2” (5.08 cm)clearance between the chock and any vehicle body panel or its components.

GENERALa. 2021 Hyundai Venue has approximately 6.69 in. (16.99 cm) minimum ground clearance.b. Seat Belt(s) must be worn at all times.c. Vehicle must be shipped with its front tires in the straight forward position, the

transmission in “Park” position and its parking brake fully engaged.

1

R2

Specifications 1.6L T I4 MPI 121 hp. @ 6,300 rpm

Curb weight range: 2,612 lbs. – 2,738 lbs. (1,184.78 kg – 1,241.94 kg) Minimum ground clearance: 6.69” (16.99 cm)

Wheelbase: 99.2 in. (251.97 cm)Length: 159.1 in. (403.86 cm) Width: 69.7 in. (177.04 cm)

Height: 61.6 in. w/rails (156.46 cm)Wheels: 15” Steel/Alloy or 17” Alloy (38.10 cm or 43.18 cm)

Transmission: 6 Speed Manual or i-VT Automatic*All weights and dimensions are subject to change without notice.

X

Technical BulletinDate:

HYUNDAI KIA MODEL YEAR: MODEL CODE:

SUBJECT:

COMMENTS:

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY 714-435-2960

Page 1 of Revision

NUMBER:

GHK1902R1 02/25/2019

ALL ALLX

SEAT BELTS MUST BE WORN AT ALL TIMES

1R1

X

IMPORTANT NOTICE TO ALL: RAIL, HAULAWAY, VPC AND SHUTTLE DRIVERS

Many newer Hyundai, Genesis and KIA models are now being delivered with state-of-the-art electronics and safety systems. These new safety systems are designed to ensure that a vehicle’s transmission is placed into ‘Park’ position if a vehicle door is opened while the driver’s seatbelt is not latched.

The following policy is established for all Hyundai, Genesis and KIA model lines going forward:

* SEAT BELT(S) MUST BE WORN BY DRIVERS AT ALL TIMES.THIS INCLUDES ANY PASSENGERS THEREOF.

Failure to follow this policy while loading, unloading, storing or driving any vehicle traveling at a speed greater than 2 mph and opening a vehicle door can cause serious physical Injury.

Technical BulletinNUMBER:

GHK2008R0Date:

08/25/2025HYUNDAI

XKIA

XMODEL YEAR:

ALLMODEL CODE:

ALLSUBJECT:

All Hybrid Vehicles Must Be Fully Turned OFF After Driving

COMMENTS:

IMPORTANT NOTICETO: RAIL, HAULAWAY, VPC AND SHUTTLE DRIVERS

The following policy is established for all Hyundai, Genesis and KIA modellines going forward:

Electronic FSE reports have shown there have been a number

of hybrid vehicles started, driven onto or off the railcars at rail

destinations and their ignition systems were never fully turned off.

Improper vehicle handling causes battery deterioration or failure.

As designed, when started, a hybrids may turn-off its internal

combustion engine, giving the false impression to the operator

that engine had have been turned off, when vehicle is still in READY

mode drawing electrical current from its main battery.

When turning hybrid engines off, please ensure that instrument panelis off and READY mode is no longer displayed. If units are turned

off properly, the dash instrument cluster will be off and vehicle READY

mode is no longer displayed.

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY714-435-2960

Page 1 of 1 Revision R1

Technical BulletinNUMBER:

GHK2007R0Date:

07/15/2020HYUNDAIGENESIS

XKIA

XMODEL YEAR:

ALLMODEL CODE:

ALL

SUBJECT: Vehicle ‘No Start’ Conditions

COMMENTS: IMPORTANTNOTICERAIL, HAULAWAY, VPC AND SHUTTLE DRIVERS

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY714-435-2960

Page 1 of 1 Revision R0

This bulletin is to help clarify, and not intended to replace any procedure published in the Appendix ‘D’ of the GLOVIS In-Transit Repair Procedures.Vehicle No Start Conditions:If vehicle’s starter turns, but does not start: Check vehicle’s fuel gage. Add 87 octane fuel if required.If vehicle’s starter does not engage but the horn sounds: Place your foot on brake petal, and gently cycle the transmission shifter from ‘Park’ (P) into the ‘Drive’ (D) position - 2 times. This will help the range switch recognize the transmission control module “Park” signal helping to place the vehicle into the proper start mode. Never use force to move the gear shifter out of ‘Park’ (P) position, or the vehicle’s shifter interlock system can be damaged. Ensure that the shifter is returned to the ‘Park’ (P) position and restart vehicle using normal start procedures.If the shifter cannot be easily moved out of ‘Park’ position, utilize the ‘Shift Lock Release’ button to move the shift lever from Park (P) into the Neutral (N) position. Press and hold the vehicle’s brake pedal. Using a wooden release tool, carefully remove the ‘Shift Lock Release’ cover/tab found near the shifter on the console panel. Insert a wooden release tool into the ‘Shift Lock Release’ hole and press down on the release button. Orange wood sticks (3.5 mm dia. x 110 mm lg); or similar product can be utilized to unlock the shift released button and can be purchased on Amazon.com. While pressing the Shift Lock Release button with the orange wood tool, press and hold in the shift knob button on the shifter handle, and gently move lever into the neutral (N) position. Use the car's key to start the vehicle. See Appendix ‘D’ or the ‘KIA Shift Interlock' video on GLOVIS website: http://america.glovis.net/English/ Magazine/List.aspx?m=29.Vehicles with “Smart Keys.” If stop lamp fuse is blown, the vehicle will not start as normal. Start the engine by pressing the Engine Start/Stop button for 10 seconds while it is in the ACC position. For your safety, always depress the brake pedal before starting any engine.EV, Hybrid and Fuel Cell vehicles. Ensure the smart key is inside the vehicle. Fully engage the parking brake. Ensure the automatic transmission shift lever is in (Park) ‘P’ position. Depress the brake pedal fully. Do not depress the accelerator. Press the ENGINE START/STOP button for 1 second or until the READY lamp in the gauge cluster illuminates. EV recharging is restricted to trained personnel only. High voltage cables and connectors are orange in color. Do not touch high voltage components, cables or connections without proper protective gear. Failure to observe this warning could result in electrical shock, injury or even death.No-start condition due to a dead battery. It is recommended to either jump-start, or charge the battery in order to move the vehicle. Jump-starting can be accomplished by using a portable booster battery (jump box), or standard jumper cables with fully insulated clamp handles. If not utilizing a portable battery jump box, jump-start using a utility truck, etc. never utilize another new car out of yard inventory. Use only 12-volt jumper systems. You can damage a 12-volt starter, ignition system, and other electrical parts beyond repair by using any system other than a 12-volt system. See Appendix ‘D’ or the ‘How to Jump Start’ video on GLOVIS website: http://america.glovis.net/English/ Magazine/List.aspx?m=29. Should you require further assistance on a ‘No Start’ vehicle, please contact the GLOVIS In-transit Repair Administrator (866-4GLOVIS).

Technical BulletinNUMBER:

GHK20716R1Date:

07/16/2020HYUNDAIGENESIS X

KIAX

MODEL YEAR:

ALLMODEL CODE:

ALL

SUBJECT: GLOVIS COVID-19 PROTOCOL UPDATE

Unfortunately, due to reported increase in the COVID-19 (Corona virus) infection rates in California and other States; we are asking our carriers to continue to be diligent and ensure that your employees, owner operators and trip-leased carriers comply with the health protocols in place at all GLOVIS ports, rail and dealership facilities where applicable.

Any driver or employee complaining or exhibiting common symptoms of the COVID-19 like a fever, cough, etc. should be screened by their healthcare professional. Only when the driver or employee is released by their doctor as being negative for COVID-19 or standard flu symptoms, should they be returning to work.

Please continue to emphasizing PPE mask wearing and social distancing in States where required, and continuous hand washing / sanitizing as recommended by CDC.

We appreciate your continued efforts and hope that this up-tick in infection rates is short lived, so our lives and businesses can quickly get back to normal.

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY714-435-2960

Page 1 of 1 Revision R1

Technical BulletinNUMBER:

GHK2010R0Date:

10/20/2020HYUNDAIGENESIS

XKIA

XMODEL YEAR:

ALLMODEL CODE:

ALL

SUBJECT: Reporting Undelivered Vehicles Left in Bays

COMMENTS: IMPORTANTPOLICY NOTICE

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY714-435-2960

Page 1 of 3Revision R0

GLOVIS VPC’s, Ports and rail heads have been inundated with a number of unreported vehicles being removed from driver load sheets, leaving both damaged and undamaged vehicles sitting in bays or load lines for days or weeks without being reported to a GLOVIS Vehicle Logistics representative.

Effective immediately, all GLOVIS contract carriers are required to report any vehicle removed from a driver’s initial load sheet and left behind at a VPC, Port or rail location. Undelivered vehicle VIN information and location information must be emailed or FAX their GLOVIS VPC, Port or GLOVIS VL representative within 4 hours of removal from a drivers load sheet on a daily basis. This requirement extends to contract carriers utilizing sub contactors where any vehicle was placed on a load sheet, but subsequently removed from the carrier’s load sheet a for any reason.

Please use the attached form on page 3, or use similar electronic version of the same and forward the information to the vehicles originating GLOVIS VPC, Port or Rail ramp’s GLOVIS vehicle logistics representative.

Plant VPC’s: Montgomery - Christian Lodge ChristianLodge@glovisusa.com; Teresa.elam@glovisusa.comRodrigus.felder@glovisusa.com; Kmoorer@glovisusa.com

West Point - Jennifer Moseley JMoseley@glovisusa.com; Sheree.bailey@glovisusa.comWeyman.scott@glovisusa.com

Ports: Brunswick - David Mason David.Mason@glovisusa.comHueneme - Victor Dunton VDunton@glovisusa.com

Portland - Bob Mazer BMazer@glovisusa.com; Roxann.Hockaday@autowc.com; Richard.Browne@autowc.com

Philadelphia – Nolan Clay NClay@glovisusa.comNational City - Mark Sur MSur@glovisusa.comShreveport - Jeffery Oge JOge@glovisusa.com

Tacoma - Jeff Risteen JRisteen@glovisusa.com; GStubberfield@glovisusa.com; Lance.Neumann@autowc.com; Royce.Dymacek@autowc.com; Jeff.Pessemier@autowc.com; Brent.Johnson@autowc.com; Doug.Hummer@autowc.com; tacomaguard@autowc.com

Technical BulletinNUMBER:

GHK2010R0Date:

10/20/2020HYUNDAIGENESIS

XKIA

XMODEL YEAR:

ALLMODEL CODE:

ALL

SUBJECT: Reporting Undelivered Vehicles Left in Bays

COMMENTS: IMPORTANTPOLICY NOTICE

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY714-435-2960

Page 2 of 3Revision R0

Rail ramp GLOVIS Representative:

Ramp Facility Name Carrier Oversee Email Ramp Facility Name Carrier Overseen By Email

ALBNM Albuquerque BNSF Jose JOrtiz@glovisusa.com PEATX Pearland BNSF Jose JOrtiz@glovisusa.comALLTX Alliance BNSF Carlos CHernandez@glovisusa.com PHOAZ Phoenix UP Jose JOrtiz@glovisusa.comANNMD Annapolis CSX Carlos CHernandez@glovisusa.com POROR Portland BNSF Austin ALam@glovisusa.comPOLOR Barnes Yard UP Austin ALam@glovisusa.com RICCA Richmond BNSF Austin ALam@glovisusa.comBIGCO Big Lift BNSF Jose JOrtiz@glovisusa.com ROLCO Rolla UP Jose JOrtiz@glovisusa.comCHHIL Chicago Heights UP Carlos CHernandez@glovisusa.com ROPUT Roper UP Austin ALam@glovisusa.comEBRMA East Brookfield CSX Carlos CHernandez@glovisusa.com SAIMN Saint Paul (Dayton's Bluff) BNSF Jose JOrtiz@glovisusa.comELMAZ El Mirage BNSF Jose JOrtiz@glovisusa.com SABCA San Bernardino BNSF Austin ALam@glovisusa.comELWIL Elwood (Logistics Park) BNSF Carlos CHernandez@glovisusa.com SANNM Santa Rosa UP Jose JOrtiz@glovisusa.comKENTX Houston Intermodal TerminKCS Carlos CHernandez@glovisusa.com SELNY Selkirk CSX Carlos CHernandez@glovisusa.comKANMO International Freight GatewKCS Carlos CHernandez@glovisusa.com TWIPA Twin Oaks CSX Carlos CHernandez@glovisusa.comKANKS Kansas City BNSF Jose JOrtiz@glovisusa.com WIMDE Wilmington NS Carlos CHernandez@glovisusa.comLAUMT Laurel BNSF Austin ALam@glovisusa.comLOROH Lordstown CSX Carlos CHernandez@glovisusa.comMESTX Mesquite UP Carlos CHernandez@glovisusa.comMILCA Milpitas UP Austin ALam@glovisusa.comMIRCA Mira Loma UP Austin ALam@glovisusa.comNAVPA Navy Yard NS Carlos CHernandez@glovisusa.com

Technical BulletinNUMBER:

GHK2010R0Date:

10/20/2020HYUNDAIGENESIS

XKIA

XMODEL YEAR:

ALLMODEL CODE:

ALL

SUBJECT: Reporting Undelivered Vehicles Left in Bays

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY714-435-2960

Page 3 of 3Revision R0

Technical BulletinNUMBER:

GHK2009R0Date:

09/25/2020HYUNDAIGENESIS X

KIA

XMODEL YEAR:

ALLMODEL CODE:

ALL

SUBJECT: Standard STI / Key Control Process

COMMENTS: IMPORTANT NOTICESTANDARD STI / KEY CONTROL PROCESS

NOTE: This process is only applicable to those dealers actively participating in STI deliveries.

1) The contract carrier or its trip leased or owner operator, within 8 hours prior to

delivery, is to notify the receiving dealership Point of Contact (POC) and advise them

that an STI delivery will be made.

2) Vehicles must be delivered to the dealership’s designated after-hours parking area

(or otherwise area as directed by POC).

3) All vehicle keys must be placed in an envelope and driver is to write the delivery

date, time, and his name on the outside of the envelope and “STI”. If shipment was

a trip lease, driver is to include contract carrier’s name, if applicable. Lastly, driver is

to legibly write or print his POC’s name or his dispatcher’s name and their phone

number on the envelope. All delivered vehicles windows must be fully closed and

vehicle doors locked.

4) Key envelope and manual delivery receipt (if not EPOD) are to be placed in the

dealers’ service department’s key drop box.

5) Upon completion of delivery, the carrier is to notify the dealer’s POC to confirm

vehicles delivery, drop location and key envelope placement. Carrier is also to

remind dealer he has 2 business days to inspect vehicles and confirm delivery on

the carriers’ EPOD web confirmation page, or return the manual delivery receipt by

any traceable means email, fax or USPS.

Following this standard process will help ensure safe and secure STI vehicle deliveries.

17305 Von Karman, Suite 200Irvine, CA 92614

QUALITY714-435-2960

Page 1 of 1 Revision R0