6 - EQUIPOS

CODIGO SERVICIOS EQUIPO/HTAS SOLICITADOS CUMPLE EQUIPO/HTAS OFRECIDOS

10002278 Registro evaluacin CBL/VDL/ cement Cargo Basico10023687 Registro evaluacin CBL/VDL/ ceme *profu10023688 Registro evaluacin CBL/VDL/cement * pie registrado10002536 Registro Gamma Ray CCL Bsico10000230 Registro Gamma Ray CCL Profundidad10000231 Registro Gamma Ray CCL Registro10009744 Cargo bsico operacin10000368 Cargo por profundidad10009523 canasta limpiadora profundidad10000746 Bridge Plug o cement retainer 7"10000745 Bridge Plug o cement retainer 9-5/8"10023634 Bridge Plug o cement retainer 7" - Fast Drill10023633 Bridge Plug o cement retainer 9-5/8" - Fast Drill10023689 Asentamiento tapones - Adapter Kit10023690 Asentamiento tapn rete * Asentamiento10009520 Registro Especial evaluacin de cemento - cargo bsico10023632 Reg evaluacin de cemento - CBL combinado - cargo bsico10000482 Registro Especial evaluacin de cemento - Cargo por profundidad10000702 Registro Especial evaluacin de cemento - Cargo por pie registrado

Registro Especial evaluacin de cemento/CBL - Cargo por profundidadRegistro Especial evaluacin de cemento/CBL - Cargo por pie registrado

10002536 Registro de Saturacin - Cargo bsico10000368 Registro de Saturacin Cargo por profundidad10015992 Registro de Saturacin Cargo por pie registrado10023625 Cortador quimico tbg 2-3/8"-2-7/8"-3-1/2"-4-1/2" bsico10023624 Cortador quimico tbg 2-3/8"-2-7/8"-3-1/2"-4-1/2" * profund10023623 Cortador quimico tbg 2-3/8"-2-7/8"-3-1/2"-4-1/2" * disparo10023639 String shot Cargo bsico10000255 String shot * profundidad10000254 String shot * disparo10023638 Tubing puncher cargo bsico10023637 Tubing puncher cargo * profudnidad10023636 Tubing puncher cargo * disparo10023644 Jet Cutters tbg 2-3/8"-2-7/8"-3-1/2"-4-1/2" bsico10023643 Jet Cutters tbg 2-3/8"-2-7/8"-3-1/2"-4-1/2" * profundidad10023642 Jet Cutters tbg 2-3/8"-2-7/8"-3-1/2"-4-1/2" * disparo10023645 Free point cargo bsico10023649 Free point cargo * profundidad10023648 Free point cargo * carrera10017703 Empaque de prueba Mecnico 7" SI Expro Group. Empaque mecnico JS, 7"10017701 Empaque de prueba Hidrulico 7" SI

Operador de empaques SI10017697 Empaque de prueba Mecnico 9-5/8" SI Expro Group. Empaque mecnico JS, 9 5/8"10023650 Empaque de prueba Hidrulico 9-5/8" SI10017699 Muestreador de fondo SI Baker. 5", 10000 psi, 1200 cc capacidad10018861 Vlvulas multip cierres Presin (tipo LPR) SI Tester valve, vlvula de flujo mltiple

CORRELACIN GR-CCL

ASENTAMIENTO TAPONES CON E-LINE

REG ESPECIAL EVALUACION CEMENTO-GR-CCL

REGISTRO SATURACION/GR/CCL

CORTADORES QUIMICOS

BACK-OFF (STRING SHOT)

TUBING PUNCHER

JET CUTTERS

DETERMINACION FREE POINT SI Applied Electronics Systems.

DST

SI

SI

Cargas de circulacin UZI.

Cortador explosivo.

SIPipe Recovery System. Cortadores qumicos nicamente para tubingde 2 3/8", 2 7/8" y 3 1/2". No contamos con cortador quimico paratbg 4 1/2".

SI Applied Electronics Systems.

NO No contamos con esta herramienta.

NO No contamos con esta herramienta.

SITitan Specialties Ltd. GR-CCL perforating and logging scintillation andgeiger, 1 11/16" y 3 1/8".

Alpha Oil Tools. Big Boy Bridge Plug, 7" y 9 5/8".SI

RELACION DE EQUIPOS OFRECIDOS

SERVICIO CAONEO DST-TCP-LOGGING

REGISTRO ELECTRICOS

SIComputer Sonic Systems. Multiplex Radial Bond Tool (SCBL-VDL-GR-CCL), 14 ft de long., 3.125" diametro.

CBL - VDL (EVALUACION DE CEMENTO)

CODIGO SERVICIOS EQUIPO/HTAS SOLICITADOS CUMPLE EQUIPO/HTAS OFRECIDOS10018859 Vlvulas multip rotac-Peso & Tensin (tipo DCIP) NO No contamos con esta herramienta10018857 Vlvulas multip Peso & Tensin (tipo Hydrospring) NO No contamos con esta herramienta10018855 Vlvula Circul-Multiciclo Presin (tipo Omni) SI Circulating valve, vlvula de circulacin mltiple10018852 Vlvula Circul-Multic Peso & Tensin (tipo HCV) SI Upstrain - Un loader Model PVC-1, 2 3/8"10018851 Vlvula Circulacin-1 ciclo (Tipo RD) SI Reversing valve, vlvula de circulacin de disco de ruptura10023654 Vlvula Flapper para prueba de tubera (tipo TST) SI Single cycle ball valve, vlvula para prueba de tubera10023653 Vlvula BPV - Bar Pressure Vent SI Bar activated vent10023652 Vlvula POV - Pressure Operated Vent NO No contamos con esta herramienta10009729 Tapones recuperables 7" (tipo RBP) SI Map Oil Tools, 5 7/8" O.D.10009731 Tapones recuperables 9-5/8" (tipo RBP) SI Map Oil Tools, 8 1/4" O.D.10009733 Union de seguridad 7" SI Bowen Oil Tools, 3 1/2" IF, 4 3/4" O.D.10009734 Union de seguridad 9-5/8" SI Bowen Oil Tools, 3 1/2" IF, 4 3/4" O.D.10023692 Martillo hidrulico SI Alpine - Weatherford. Total stroke 10, 4 1/2" O.D.10023658 Shock Absorver Radial SI Tripoint, 5", 10000 psi, mx presin dif: 10000 psi10023657 Shock Absorver Vertical SI Tripoint, 5", 10000 psi, mx tensin: 140000 lbs10023656 TCP-DST Operador SI10023655 TCP-DST Ayudante SI

TCP CARGO BASICO SI10000267 TCP. 4 1/2" dp 4 SPF 32 GR SI 4 1/2", 4 SPF, 39 GR, 52" penetracin, # 10121063610000268 TCP. 4 1/2" dp 6 SPF 32 GR SI 4 1/2", 5 SPF, 39 GR, 52" penetracin, # 10121063610000269 TCP. 4 1/2" dp 8 SPF 22.7 GR SI 4 1/2", 8 SPF, 23 GR, 30.86" penetracin, HSC-4000-411NTII10000279 TCP. rdx dp Espaciador 4 1/2" SI10000287 Cabeza disparo Annular firing head SI10000288 Cabeza disparo Mechanical firing head SI10000289 Cabeza disparo Time-delay firing head SI10000281 TCP 3 3/8" DP 4 SPF 24 GR SI 3 3/8", 4 SPF, 25 GR, 41.39" penetracin, SDP-3375-411NT310000282 TCP 3 3/8" DP 6 SPF 24 GR SI 3 3/8", 6 SPF, 25 GR, 41.39" penetracin, SDP-3375-411NT310000283 TCP Espaciador 3 3/8" DP SI10000301 Marca radiactva SI10000316 Casing gun cargo bsico SI10000317 Casing gun (cable elctrico) Primeros 20 tiros SI10000318 Casing gun (cabl elct) Tiro adicional SI10000224 THRU TUBING Caoneo Std 2-1/8" Bsico SI 2 1/8", 4 SPF, 13.9 GR, 26.93" penetracin, STP-2125-401NTX10000225 THRU TUBING Caoneo Std 2-1/8" Primeros 20 tiros SI 2 1/8", 4 SPF, 13.9 GR, 26.93" penetracin, STP-2125-401NTX10000226 THRU TUBING Caoneo Std 2-1/8" Tiro adicional SI 2 1/8", 4 SPF, 13.9 GR, 26.93" penetracin, STP-2125-401NTX10014157 THRU TUBING Caoneo Std 1-11/16" Bsico SI 1 11/16", 4 SPF, 8.4 GR, 19.31" penetracin, STP-1687-401NTX10014158 THRU TUBING Caoneo Std 1-11/16" Primeros 20 tiros SI 1 11/16", 4 SPF, 8.4 GR, 19.31" penetracin, STP-1687-401NTX10014159 THRU TUBING Caoneo Std 1-11/16" Tiro adicional SI 1 11/16", 4 SPF, 8.4 GR, 19.31" penetracin, STP-1687-401NTX

CAONEO

DST

SOLICITUD DE OFERTAS N 040-24954-25065-06

PROPUESTA TECNICO-ECONOMICA EVC2006-095

Caoneo y otros servicios especiales en hueco revestido Mayo 23 de 2006

REGISTROS CASED HOLE




SERVICIO REGISTROS CASED HOLE

1. Unidad de Registro Unidad de registro hidrulica provista con doble malacate (Cable 7/32 y 5/16), winche, cabina-laboratorio, sistema computarizado para adquisicin de datos, etc. Caractersticas: Motor CUMMIS 290 Potencia 290 HP RPM 2.100 Freno Mecnico (banda) y aire Sistema Winche Hidrulico Generador Marca POWER TECHNOLOGY Inc. Voltios 120 Amperios 27 Frecuencia 200 Hz Cantidad 2 Tambor Cable Elctrico: Dimetro 122 in Longitud 11 Cable Elctrico: Marca CAMESA Dimetro 7/32 Longitud 16.000 ft Temp. Mx. 400 F Marca CAMESA Dimetro 5/16 Longitud 16.000 ft Temp. Mx. 400 F Hardware de Registro: SCIENTIFIC DATA SYSTEM para caoneo y registro CCL y GR-CCL

Monitor 14




CPU 1 Battery Pack 1 UPS 1 Impresora (Plotter) Road Power

Software:

Windows 2000, XP, Me Warrior System

Camin:

Marca INTERNATIONAL Motor Cummis 290

Carrocera:

Tipo FURGN Laboratorio:

Aire Acondicionado Panel de winche RAP con equipo de registro

2. Equipo de Control de Presin Equipo de control de presin en 5 y 7. Compuesto por:

Tree Connection BOP (con rams para cable 7/32 o 5/16) Lubricador Stuffing Box Poleas (Cable 7/32 o 5/16) Estrobo para correlacin Manmetros Mangueras de Alta Presin




3. Registro GR-CCL

Marca TITAN SPECIALTIES LTD Tipo Logging / Geigger Muller Voltaje cabeza 120 VDC (positivo) Corriente 57 mA Tiempo 10 ft/min 6 seg, 20 ft/min 3 seg 30 ft/min 2 seg Longitud 75.88 in Dimetro 1 11/16 Peso 28 lb Rango de Presin 20.000 psi Espaciamiento mecnico CCL a GR 41.4 in

Titan Instrument Division P.O. Box 2316, Pampa, TX 79066 Tel. 800-692-4486 Fax 806-669-6674 40 www.titangroup.net

SPECIFICATIONS

MODEL NUMBER

8100-31257SC100-04-01

Perforating configuration with CCL

MAX TEMPERATURE RATING

350 F (176.7 C) *

PRESSURE RATING

20,000 PSI (138 MPa)

OPERATING VOLTAGE

(Gun fires on Negative Voltage)

120 VDC, Positive

OPERATING CURRENT

60 mA

AVAILABLE OPTIONS

HS Resistant Material

Other Subs available

* Lower temperature models

Voltage from 50 150 VDC

3 1/8 INCH

(7.94 CM)

3 1/8 in (7.94 cm) Perforating Scintillation Gamma Ray with CCL

027B

31A

0 A

pr-0

5


SPECIFICATIONS

MODEL NUMBER as shown

8130-168B2MC129-02-00

MODEL NUMBER no bottom

8130-168B2MC129-02-0X

MAX TEMPERATURE RATING

500 F (260.0 C) *

PRESSURE RATING

20,000 PSI (138 MPa)

OPERATING VOLTAGE

120 VDC, Positive

OPERATING CURRENT

10 mA

AVAILABLE OPTIONS

Negative Power Constant Current Power HS Resistant Material

* Lower temperature models available

1 11/16 INCH

(4.29 CM)

1 11/16 in (4.29 cm) Logging CCL

300B

16A

0 A

pr-0

5


SPECIFICATIONS

MODEL NUMBER as shown

0257-500-001

TEMPERATURE RATING

500 F (260.0 C)

PRESSURE RATING

20,000 PSI (138 MPa)

ALSO AVAILABLE

0257-500-011

Fish Neck Top / Bottom accepts QC

0257-500-020

Go Box Top / Go Box Bottom

SPECIAL FEATURE

Bottom accepts Quick Change

AVAILABLE OPTIONS

Can be purchased with Quick Change Assembly

HS Resistant Subs

3 1/8 INCH

(7.94 CM)

3 1/8 in (7.94 cm) Passive Shooting CCL

301B

31A

0 A

pr-0

5




4. Sector Cement Bond Log (SCBL)

La herramienta Multiplex Radial Cement Bond tiene adems del receptor de 3 ft y el receptor de 5 ft, un cristal segmentado localizado a dos (2) ft bajo el transmisor. Este cristal tiene forma cilndrica, de 2 de dimetro y 2 de longitud. Est dividido en 8 sectores, cada uno de los cuales cubre 45 del well bore. MARCA COMPUTER SONIC SYSTEM TIPO MULTIPLEX RADIAL SONDE VOLTAJE CABEZA 120 Voltios (Mnimo) CORRIENTE 80 mA TIEMPO 153 milisegundos (Completo set de datos) LONGITUD 14 ft (sin centralizador) DIMETRO HTA 3.13 in DIMETRO ELECTRICO 2.50 in PESO 220 lb (sin centralizador) RANGO DE TEMPERATURA -20 / 350 F PRESION DE DISEO 20.000 psi RANGO DE OPERACIONES CSG 4 9 5/8 DE REGISTRO CARACTERSTICAS: Diseada para ofrecer un registro de adherencia de cemento

completo (360) Suministra medidas de amplitud, impedancia y tiempo de

trnsito (tren de onda) COMPONENTES DE LA HERRAMIENTA:

9 Receptores 10 receptores de cristal piezoelctrico Un receptor cercano (3 ft) Un receptor lejano (5 ft) Ocho (8) receptores radiales

9 Transmisores Un transmisor de cristal piezoresistivo

9 Detector Gamma Ray Cristal de centelleo con tubo PM (disponible la opcin Flask)




Dimensiones cristal de centelleo 1.36 x 3 9 Seal de calibracin

Seal de referencia de calibracin en el pozo 9 Probador de Temperatura

Resistencia de platino tipo RTD 9 Localizador de Cuellos Magnticos

Imn especial a tierra 9 Telemetra

Canales digitales de 10 16 bytes PRESENTACIN REGISTRO SCBL: El registro SCBL presenta las siguientes curvas:

Gamma Ray, CCL, tiempo de trnsito (tt), Temperatura

Recibo de seal (amplitud) del receptor de 3 ft y ampliada

Recibo de seal del receptor radial (2 ft) con la amplitud mxima, mnima y promedio

Registro Variable de Densidad (VDL), el cual se deriva directamente del tren de

ondas de la seal del receptor de 5 ft.

Mapa de Contorno del receptor radial, el cual se muestra en el ltimo track y es la representacin grfica de la respuesta de las medidas de los 8 sectores. La forma del mapa de cemento es una representacin de las lecturas de amplitud de los diferentes sectores.

El Mapa de Cemento es una representacin visual de las condiciones del cemento detrs de la tubera. El cristal del receptor radial no es libre de rotar dentro de la herramienta, sin embargo la herramienta en s misma puede rotar dentro del pozo. Por esta razn, los canales en el cemento pueden rotar aparentemente dentro del Mapa de Cemento cuando se hacen corridas repetidas, y la representacin grfica no se repite exactamente igual. Cada sector individual es representado por una seccin del mapa de cemento. El nico factor bajo control del ingeniero de registros es el valor del color negro y blanco de la presentacin del registro del receptor radial. El propsito del Mapa de Cemento es ilustrar grficamente pequeos canales que pueden ser




un problema. El Mapa de Cemento es una importante ayuda para identificar fcilmente problemas en la herramienta o en el procedimiento de registro.

5. Hydraulic Setting Tool MARCA ALPHA OIL TOOLS DIAMETRO 4.125 TEMPERATURA 350 F PRESION MAX. 15.000 psi LONGITUD 6.2 ft. Caractersticas: Permite un exitoso sentamiento de Bridge Plugs, Retenedores de Cemento,

Empaques de Produccin, etc. La presin permanece confinada en la porcin correcta de la herramienta, por

medio del uso de sello ORing, los cuales deben encontrarse en perfecto estado debido a su funcin crtica.

MULTIPLEXRADIAL BOND TOOL

(expandable to 16 in Version 2), anda full-time sonic calibration refer-ence signal are transmitted in everytool transmission cycle.

Multiplexing allows sonic signals tobe transmitted to the surface at frequency of conventional CBL tools.This dramatically lowers the signal-to-noise ratio. Lower frequencyallows the CSS MRBT to easily runon all types of wireline includingnickel (sour service) wireline.

The CSS MRBTs electronics aredesigned and tested to operate at350F (175C). The Multiplex II istested to 375F (190C), allowinggreater logging flexibility. All CSSMRBT tools are pressure tested to20,000psi (137.9 MPa). The Multi-plex II is soak tested at 350F and18,000psi for 4 hours, demonstrat-ing the ability to withstand the mostrigorous logging conditions.

Computer Sonics Systems MultiplexRadial Bond Tool (MRBT) offershigh quality Radial Bond logging

capability at a fraction of the cost of similartools. The CSS MRBT is a cost effectivesolution to all of your bond logging needsand contains an integrated collar locator(CCL), gamma ray detector, and tempera-ture probe.

We make our tools from the highest qualitymaterials to withstand the rigors of dailyuse. Every Bond tool that we have evermanufactured is still used in the field today.

The CSS MRBT has the lowest per-runmaintenance cost of any tool of this type.Modular design makes maintenance andrepair possible with a minimum of training.

Handling and transport of the CSS MRBT iseasy. The tool weighs just 215lbs (97.5kg)and splits into two 7.5ft (2.28m) sections.

Patented high speed Multiplexed datatransmission allows the MRBT to be loggedat 45ft/min (15m/min) at a vertical resolu-tion of 0.10ft (0.03m). Eleven full wavesonic signals, 10 channels of telemetry

Call:Toll Free in North America1-800-406-7770Phone: +403 -235-6533Fax: +403-235-6737

Or visit us on the web:www.compsonsys.com

CSSCOMPUTERSONICSSYSTEMS INC.

The CSS MRBT's electronics aredesigned and tested to operate at 350oF (175oC). The Multiplex II istested to 375oF (190oC), allowing greater logging flexibility. MXII toolsare pressure tested to 20,000 psi(137.9 MPa). The MXI is pressuretested to 17,000 psi (117.2 MPa). TheMXII is soak tested at 350o F and18,000 psi for 4 hours, demonstratingthe ability to withstand the mostrigorous logging conditions.

SPECIFICATIONS

Length(w/ centralizers)

Length(w/o centralizers)

Tool Diameter

Dimensions

MULTIPLEX MULTIPLEX II14 ft4.27 m

14 ft4.27 m

18. 75 ft (2 centralizers)5.72 m

22 ft (3 centralizers)6.71 m

3.125 in7.94 cm

3.125 in7.94 cm

Weight(w/o centralizers)

220 lb100 kg

230 lb104.3 kg

Tool Cycle Time 153 milliseconds 153 milliseconds

Head Voltage 120V@80mA 120V@105mA

Design Pressure 20,000 PSI Rated

O-ring assembly

20,000 PSI Tested Max.18, 000 PSI WorkingT-seal assembly

Operating TemperatureRange (no flask required)

-20oF to 350oF

-30oC to 175oC

-20oF to 375oF Tested Max.350oF Working30oC to 190oC

External TemperatureMeasurement

Analog Digital(providing improved stability)

Telemetry

Assembly Connections Standard Thread Field Joint (for better handlingin wet conditions)

10 - 16 bit channels @10KHz

10-16 bit channels @ 10KHz(switchable 16-16 bit channels@ 6KHz for improved sourline operation)

Receivers 8 - 2 ft receivers1 -3 ft receiver1 -5 ft receiver

8 - 2 ft receivers1 -3 ft receiver1 -5 ft receiver

Transmitter Single transmitterSingle transmitter

Transmitter Linearity up to 20% change at 350oF less than 10% change at 350oF

Calibration Signal Internal Internal

Built-in Gamma Ray andCollar Locator

Accepts Additional Bot-tom End Tools

Included

Yes

Included

Yes

17,000 PSI Rated

Big Boy Bridge Plug Wireline Set

The Big Boy Bridge Plug has proven to be a product that can be depended on. It has excellent running characteristics and secure sets. The plug can be set on different types of wireline pressure setting tools. The Big Boy is designed for rapid drill-out while maintaining sufficient strength during the set. This plug sustains high pressures and temperatures. FEATURES: Electric wireline set Drillable Cast iron construction One piece slips - hardened to depth of wicker only Sets in any grade casing including P-110 Form-fitting metal back-ups prevent rubber extrusion For temporary or permanent service Ratcheting lock ring holds setting force

SPECIFICATIONS

This illustration does

not reflect all sizes

CASING PLUG SETTING RANGE SETTING TOOL OD WT. (LBS/FT) PART NO. O.D. MIN. MAX. BAKER GO 2 3/8 3.3 - 5.9 000-1710-002 1.71 1.867 2.107 05 2 3/8 3.3 - 5.9 000-1710-000 1.71 1.867 2.107 1 11/16 2 7/8 6.4 - 6.5 000-2100-002 2.10 2.280 2.563 05 2 7/8 6.4 - 6.5 000-2100-000 2.10 2.280 2.563 1 11/16 2 7/8 6.4 - 6.5 000-2100-000 2.10 2.280 2.563 2 1/8 3 1/2 5.7 - 10.2 000-2750-002 2.75 2.867 3.258 05 3 1/2 5.7 - 10.2 000-2750-000 2.75 2.867 3.258 10 3 1/2 5.7 - 10.2 000-2750-000 2.75 2.867 3.258 1 11/16 3 1/2 5.7 - 10.2 000-2750-000 2.75 2.867 3.258 2 1/8

4 5.6 - 14 000-3120-002 3.12 3.340 3.732 10 2 1/8 4 1/2 9.5 - 16.6 000-3500-002 3.50 3.826 4.090 10 3 1/2 4 1/2 9.5 - 13.5 000-3710-002 3.71 3.920 4.560 10 3 1/2

5 11.5 - 21 000-3710-002 3.71 3.920 4.560 10 3 1/2 5 1/2 13 - 25 000-4240-002 4.24 4.580 5.047 20 3 1/2 5 3/4 22.5 - 25.2 000-4240-002 4.24 4.580 5.047 20 3 1/2

6 14 - 26 000-4750-002 4.75 5.140 5.595 20 3 1/2 6 5/8 34 000-4750-002 4.75 5.140 5.595 20 3 1/2

6 10.5 - 12 000-5340-002 5.34 5.595 6.366 20 3 1/2 6 5/8 17 - 34 000-5340-002 5.34 5.595 6.366 20 3 1/2

7 23 - 40 000-5340-002 5.34 5.595 6.366 20 3 1/2 6 5/8 17 - 22 000-5610-002 5.61 5.989 6.655 20 3 1/2

7 17 - 35 000-5610-002 5.61 5.989 6.655 20 3 1/2 7 5/8 20 - 39 000-6090-002 6.09 6.625 7.263 20 3 1/2 8 5/8 24 - 49 000-6960-002 6.96 7.511 8.248 20 3 1/2 9 5/8 29.3 - 53.5 000-7710-002 7.71 8.435 9.063 20 3 1/2 10 3/4 54 - 81 000-8710-002 8.71 9.250 9.784 20 3 1/2 10 3/4 32.7 - 51 000-9500-002 9.50 9.850 11.150 20 3 1/2 11 3/4 38 - 60 000-9500-002 9.50 9.850 11.150 20 3 1/2 13 3/8 77 - 102 000-1156-002 11.56 11.633 12.464 20 3 1/2 13 3/8 48 - 72 000-1200-002 12.00 12.347 12.715 20 3 1/2

16 65 - 109 000-1425-002 14.25 14.688 15.250 20 3 1/2 18 5/8 76 - 96.5 000-1725-002 17.25 17.655 18.730 20 3 1/2

20 133 - 169 000-1725-002 17.25 17.655 18.730 20 3 1/2

Big Boy Bridge Plug

Dimensional Data

Plug Size O.D. * A B C D E F G H J K 1.71 GO L 1.710 1.656 1.687 1.687 1.093 3.390 3.218 3.078 9.687 12.000

1.71 Baker L 1.710 1.656 1.687 1.687 1.093 3.390 3.218 3.078 9.687 15.875 2.10 GO L 2.100 2.031 2.062 2.062 1.250 3.296 3.812 2.796 9.906 12.218

2.10 Baker L 2.100 2.031 2.062 2.062 1.250 3.296 3.812 2.796 9.906 16.093 2.75 GO R 2.750 2.671 2.687 2.687 1.500 2.453 5.093 4.078 11.843 14.155

2.75 Baker R 2.750 2.671 2.687 2.687 1.500 2.453 5.093 4.078 11.843 18.030 3.12 R 3.120 3.062 3.062 3.062 1.875 2.390 5.250 3.952 11.843 15.718 3.50 L 3.500 3.421 3.437 3.437 2.125 4.921 5.470 4.733 15.155 15.655 3.71 L 3.710 3.625 3.648 3.648 2.125 4.921 5.470 4.733 15.155 15.655 4.24 L 4.240 4.187 4.187 4.187 2.750 4.872 5.390 5.028 15.343 15.843 4.75 L 4.750 4.687 4.687 4.687 2.750 4.872 5.390 5.028 15.343 15.843 5.34 L 5.340 5.281 5.260 5.260 3.687 5.932 7.250 5.932 19.124 ** 5.61 L 5.610 5.562 5.546 5.546 3.687 5.932 7.250 5.932 19.124 ** 6.09 R 6.090 6.015 5.968 5.968 4.125 3.860 8.859 7.132 20.250 ** 6.96 R 6.960 6.875 6.843 6.843 4.625 4.900 9.796 7.400 22.500 ** 7.71 R 7.710 7.640 7.593 7.593 5.125 5.125 10.046 7.625 23.187 ** 8.71 R 8.710 8.640 8.593 8.593 5.687 4.867 10.562 8.235 24.063 ** 9.50 R 9.500 9.375 9.375 9.375 6.750 5.644 10.562 9.011 25.594 **

11.56 R 11.56 11.437 11.437 11.437 9.000 5.750 10.609 8.250 25.969 ** 12.00 R 12.00 11.875 11.875 11.875 9.000 5.750 10.609 8.250 25.969 ** 14.25 R 14.25 14.125 14.125 14.125 11.500 6.985 8.859 10.235 26.562 ** 17.25 R 17.25 17.125 17.125 17.125 14.000 6.901 7.609 9.401 25.125 **

*- The second column indicates which illustration to use for plug dimensioning (left or right). **- The shear stud on this size does not extend above the top of the body. Some sizes differ slightly from the illustrations shown

Alpha Oil Tools Guidelines for Running Wireline Set Bridge Plugs

Use casing scraper before running any equipment in the well to remove scale and other materials from the casing wall. Any tool that is expected to grip the casing wall has to first reach the casing wall. Follow scraper with gage ring and junk basket.

Always follow cleaning, redressing and operational procedures on the setting tool. Make certain oil levels in pressure setting tool are correct for the well environment involved. Take into consideration the heat expansion of the oil in your manufacturers guidelines that should be supplied with your pressure setting tool.

Use the correct bridge plug for the temperature, pressure, casing size, casing weight and environment.

Casing should have 100% cement bond before running plug in the well.

Do not overtighten bridge plug onto setting tool. This action causes the slips to crack which leads to premature setting. Snug tight is sufficient for a bridge plug. The lock spring or nut, depending on make of setting tool, must accompany the tension mandrel to prevent plug from from backing off.

Do not allow the setting tool weight to rest on the bridge plug after making up. This can cause the slips to crack.

Help guide the setting tool and bridge plug through lubricators, wellhead and blowout preventer. When running under pressure raise tools to the top of lubricator before equalizing the pressure into lubricator.

Running speed should not exceed 300 feet per minute to avoid fluid displacement cutting on elastomer. Should setting tool misfire, retrieve equipment no faster than it went in. Slow down for liners and other restrictions.

Never set plug in casing collar or where milling has occurred. Always set plugs in static well conditions (no fluid or gas

movement). Shock to the plug can result in failure. Warn service companies of

the plug depth to avoid high impact collisions. When using the plug for locating purposes, be gentle and ease tools onto plug. Never place tubing weight on plug.

Pressure setting tool failure can result from several causes (ex: out of date power charge or bad o-ring). In the event that a pressure setting tool does not shear off of the bridge plug and you have to pull out of the rope socket, the shear stud will still part in a normal manner when the setting tool is fished out. This happens most commonly because the power charge did not put up sufficient pressure to shear the stud in the plug. The Alpha studs are made to shear correctly and are held to high standards of accuracy. When the fishing tool goes in to retrieve the setting tool, you can watch the accuracy of the shear stud when it shears, assuming that the weight indicator is not out of calibration. The shear values are listed as follows:

Size of Plug (O.D.) Shear Stud Value

1.710 thru 2.750 12,000 lbs. 3.120 25,000 lbs. 3.500 thru 4.750 30,000 lbs. 5.340 thru 12.000 50,000 lbs.

When perforating, bridge plug should be protected with a

minimum of ten feet of cement dumped directly on top of plug. Cement should be given sufficient time to set up before perforating.

Perforating should not be done closer than fifty feet of bridge plug.




CAONEO




SERVICIO DE CAONEO 1. Caones 4 1/2", 12 spf - HALLIBURTON, MILLENNIUM MARCA OWEN SDP TIPO DE CAON SCALLOPED GUN SYSTEM DIAMETRO 4 O.D. CASING 7 O.D. PESO 23 gr TIPO SDP DENSIDAD 12 tpp CARGA HSC-4000-411NTII PENETRACION 30.86 normalizado a 5000 psi (5% x 1000) TEMPERATURA 400 F PRESION 18.000 psi ENTRY HOLE 0.40 DESFACE 135/45 ANEXOS Certificado API RP19B NORMALIZACION DE CARGAS A 8,000 psi: Penetracin : 30.86 Resistencia a la Compresin: 5,877 psi Normalizando a 8,000 psi de resistencia a la compresin con el criterio de 5% de disminucin en penetracin por cada 1,000 psi de resistencia a la compresin adicional: Penetracin @ 8,000 psi = 30.86 (30.86 * {(8,000 5,877) * 0.05/1,000}) Penetracin @ 8,000 psi = 27.58

Data Sheet - Perforating System Evaluation, API RP 19B Section 1API Form 19B-Section 1

AVAILABLE TO ALL FROM OWEN OIL TOOLS 23 HMX STEEL4-1/2" TAG - 12 SPF SDP 400

3-3/8" & 4" SDP NTII 18,000 OWEN SPEC STEEL HSC-4000-411NTII 5/06/02 12

SCALLOPED RETRIEVABLE EXPENDABLE HOLLOW CARRIER 5.675 135/45 X X X

RDX VERSION AVAILABLE AS HSC-4000-311NTII

7 OD, 32 L-80 6/10/0284" OD, 8601 17152 4568

6/10/02 5877 28

No. 1 No. 2 No. 3 No. 4 No. 5 No. 6 No. 7 No. 8 No. 9 No. 10 No. 110.00 1.31 0.69 0.18 1.59 0.18 0.69 1.31 0.00 1.31 0.690.37 0.37 0.42 0.39 0.43 0.38 0.37 0.41 0.44 0.38 0.420.37 0.38 0.42 0.41 0.44 0.40 0.38 0.43 0.45 0.40 0.440.37 0.38 0.42 0.40 0.44 0.39 0.38 0.42 0.45 0.39 0.4331.50 26.40 33.30 31.40 28.20 34.60 33.00 30.90 34.00 27.50 28.750.06 0.05 0.04 0.04 0.05 0.06 0.06 0.07 0.03 0.04 0.05

No. 12 No. 13 No. 14 No. 15 No. 16 No. 17 No. 18 No. 19 No. 20 No. 21 No. 22 Average0.18 1.59 0.18 0.69 xxxxxxxx0.39 0.38 0.40 0.43 0.400.40 0.39 0.42 0.44 0.410.40 0.39 0.41 0.44 0.4033.58 29.40 30.10 30.30 30.860.04 0.07 0.05 0.04 0.05

MANUFACTURER'S CERTIFICATION

X

X Vice President - Engineering 6/11/2002 Owen Oil Tools LP 8900 Forum Way Fort Worth, Texas 76140

Service CompanyGun OD & Trade Name

Casing Data

Charge NameManufacturing Charge Part No. Date of ManufactureGun TypePhasing Tested degrees, Firing Order Top Down, Bottom UpDebris DescriptionRemarks

Target Data

Shot No.Clearance, in.Casing Hole Diameter, Short Axis, in.Casing Hole Diameter, Long Axis, in.Average Casing Hole Diameter, in.Total Depth, in.Burr Height, in.


Explosive WeightMax. Temp ^FMaximum Pressure RatingShot Density TestedRecommended Minimum ID for RunningAvailable Firing ModeDebris Weight gm/charge, Debris in3/charge

Simultaneousin.

Shots/ft

200 hr100 hr24 hr3 hr1 hrpsi, Carrier Material

Selective

gm, powder, Case Material

WeightAmount of Cement

lb/ft,lb.,Amount of Sand

API Grade, Date of Section 1 TestAmount of Water

Age of Target dayslb.,

psiBriquette Compressive StrengthDate of Compressive Strength Testlb.

Remarks

I certify that these tests were made according to the procedures as outlined in API RP 19B: Recommended Practices for Evaluation of Well Perforators, First Edition, November, 2000. All of the equipmentused in these tests, such as the guns, jet charges, detonator cord, etc., was standard equipment with our company for the use in the gun being tested and was not changed in any manner for the test.Furthermore, the equipment was chosen at random from stock and therefore will be substantially the same as the equipment that would be furnished to perforate a well for any operator. The AmericanPetroleum Institute neither endorses these test results nor recommends the use of the perforator system described.

Type of Certification: Self Third Party

CERTIFIED BYRECERTIFIED (Company Official) (Title) (Date) (Company) (Address)




2. Caones 4 1/2", 5 spf - HALLIBURTON, MILLENNIUM MARCA JRC - HALLIBURTON TIPO DE CAON SCALLOPED GUN SYSTEM DIAMETRO 4 O.D. CASING 7 O.D. PESO 39 gr TIPO MILLENNIUM DENSIDAD 5 tpp CARGA 101210636 PENETRACION 52.00 normalizado a 5.000 psi (5% x 1000) TEMPERATURA 400 F PRESION 20.000 psi ENTRY HOLE 0.37 DESFACE 60 ANEXOS Certificado API RP43 NORMALIZACION DE CARGAS A 8,000 psi: Penetracin : 52.00 Resistencia a la Compresin: 5,502 psi Normalizando a 8,000 psi de resistencia a la compresin con el criterio de 5% de disminucin en penetracin por cada 1,000 psi de resistencia a la compresin adicional: Penetracin @ 8,000 psi = 52.00 (52.00 * {(8,000 5,502) * 0.05/1,000}) Penetracin @ 8,000 psi = 45.51

Internet




3. Caones 3 3/8, 6 spf - DP MARCA OWEN OIL TOOLS DIAMETRO 3 3/8 O.D. TIPO RAPTOR DENSIDAD 6 tpp PESO 25 grm CARGA SDP-3375-411NT3 PENETRACION 41.39 TEMPERATURA 400 F PRESION 22,000 psi ENTRY HOLE 0.48 DESFACE 60 ANEXOS Certificado API RP19B NORMALIZACION DE CARGAS A 8,000 psi: Penetracin : 41.39 Resistencia a la Compresin: 6,076 psi Normalizando a 8,000 psi de resistencia a la compresin con el criterio de 5% de disminucin en penetracin por cada 1,000 psi de resistencia a la compresin adicional: Penetracin @ 8,000 psi = 41.39 (41.39 * {(8,000 6,076) * 0.05/1,000}) Penetracin @ 8,000 psi = 37.41

Data Sheet - Perforating System Evaluation, API RP 19B Section 1API Form 19B-Section 1

AVAILABLE TO ALL FROM OWEN OIL TOOLS 25 HMX STEEL3-3/8" TAG - 6 SPF, 60 DEGREE RAPTOR NT3 400

3-3/8" SDP NT3 22,000 OWEN SPEC STEELSDP-3375-411NT3 3/14/02 6

SCALLOPED RETRIEVABLE EXPENDABLE HOLLOW CARRIER 3.7560 X X X

RDX VERSION AVAILABLE AS SDP-3375-311NT3

4-1/2" OD, 11.6 L-80 4/11/0296" OD, 11234 22402 5966

4/10/02 6076 34

No. 1 No. 2 No. 3 No. 4 No. 5 No. 6 No. 7 No. 8 No. 9 No. 10 No. 110.00 0.14 0.45 0.63 0.45 0.14 0.00 0.14 0.45 0.63 0.450.45 0.45 0.50 0.47 0.51 0.46 0.45 0.49 0.52 0.46 0.500.45 0.46 0.50 0.49 0.52 0.48 0.46 0.51 0.53 0.48 0.520.45 0.46 0.50 0.48 0.52 0.47 0.46 0.50 0.53 0.47 0.5143.35 39.20 38.50 38.50 43.00 41.75 42.00 39.85 45.25 46.20 43.600.06 0.05 0.04 0.04 0.05 0.06 0.06 0.07 0.03 0.04 0.05

No. 12 No. 13 No. 14 No. 15 No. 16 No. 17 No. 18 No. 19 No. 20 No. 21 No. 22 Average0.14 0.00 0.14 0.45 xxxxxxxx0.47 0.45 0.48 0.51 0.480.48 0.47 0.50 0.52 0.490.48 0.46 0.49 0.52 0.4837.30 39.50 38.58 44.30 41.390.04 0.07 0.05 0.04 0.05

MANUFACTURER'S CERTIFICATION

X

X Vice President - Engineering 4/11/2002 Owen Oil Tools LP 8900 Forum Way Fort Worth, Texas 76140

Service CompanyGun OD & Trade Name

Casing Data

Charge NameManufacturing Charge Part No. Date of ManufactureGun TypePhasing Tested degrees, Firing Order Top Down, Bottom UpDebris DescriptionRemarks

Target Data



Explosive WeightMax. Temp ^FMaximum Pressure RatingShot Density TestedRecommended Minimum ID for RunningAvailable Firing ModeDebris Weight gm/charge, Debris in3/charge

Simultaneousin.

Shots/ft

200 hr100 hr24 hr3 hr1 hrpsi, Carrier Material

Selective

gm, powder, Case Material

WeightAmount of Cement

lb/ft,lb.,Amount of Sand

API Grade, Date of Section 1 TestAmount of Water

Age of Target dayslb.,

psiBriquette Compressive StrengthDate of Compressive Strength Testlb.

Remarks

I certify that these tests were made according to the procedures as outlined in API RP 19B: Recommended Practices for Evaluation of Well Perforators, First Edition, November, 2000. All of the equipmentused in these tests, such as the guns, jet charges, detonator cord, etc., was standard equipment with our company for the use in the gun being tested and was not changed in any manner for the test.Furthermore, the equipment was chosen at random from stock and therefore will be substantially the same as the equipment that would be furnished to perforate a well for any operator. The AmericanPetroleum Institute neither endorses these test results nor recommends the use of the perforator system described.

Type of Certification: Self Third Party

CERTIFIED BYRECERTIFIED (Company Official) (Title) (Date) (Company) (Address)




4. Caones 2 1/8, 4 spf, Semi-expendable MARCA OWEN OIL TOOLS DIAMETRO 2 1/8 TIPO RAPTOR DENSIDAD 4 tpp CARGA STP-2125-401NTX PENETRACION 26.93 TEMPERATURA 375 F PRESION 20,000 psi ENTRY HOLE 0.25 DESFACE 40 ANEXOS Certificado API RP43 NORMALIZACION DE CARGAS A 8,000 psi: Penetracin : 26.93 Resistencia a la Compresin: 5,620 psi Normalizando a 8,000 psi de resistencia a la compresin con el criterio de 5% de disminucin en penetracin por cada 1,000 psi de resistencia a la compresin adicional: Penetracin @ 8,000 psi = 26.93 (26.93 * {(8,000 5,620) * 0.05/1,000}) Penetracin @ 8,000 psi = 23.73




5. Caones 1 11/16, 4 spf, Semi-expendable MARCA OWEN OIL TOOLS DIAMETRO 1 11/16 TIPO RAPTOR DENSIDAD 4 tpp CARGA STP-1687-401NTX PENETRACION 19.31 TEMPERATURA 375 F PRESION 20,000 psi ENTRY HOLE 0.24 DESFACE 40 ANEXOS Certificado API RP19B NORMALIZACION DE CARGAS A 8,000 psi: Penetracin : 19.31 Resistencia a la Compresin: 6,463 psi Normalizando a 8,000 psi de resistencia a la compresin con el criterio de 5% de disminucin en penetracin por cada 1,000 psi de resistencia a la compresin adicional: Penetracin @ 8,000 psi = 19.31 (19.31 * {(8,000 6,463) * 0.05/1,000}) Penetracin @ 8,000 psi = 17.83

2004 Owen Oil Tools All rights reserved

Owen Oil Tools Shogun Spiral Strip* SystemShogun Spiral Strip* SystemShogun Spiral Strip* SystemShogun Spiral Strip* SystemShogun Spiral Strip* System1-11/16", 2-1/8" & 2-1/2" O.D.1-11/16", 2-1/8" & 2-1/2" O.D.1-11/16", 2-1/8" & 2-1/2" O.D.1-11/16", 2-1/8" & 2-1/2" O.D.1-11/16", 2-1/8" & 2-1/2" O.D.

Super Deep Penetrator & Big Hole Super Deep Penetrator & Big Hole Super Deep Penetrator & Big Hole Super Deep Penetrator & Big Hole Super Deep Penetrator & Big Hole

Benefits / CapabilitiesBenefits / CapabilitiesBenefits / CapabilitiesBenefits / CapabilitiesBenefits / Capabilities

6 spf in 1-11/16" & 2-1/8" versions

N.T. Shogun charge shoots 40% better than standard ShogunDP charge

40 & 60 Spiral phasing available

SpecificationsSpecificationsSpecificationsSpecificationsSpecifications

ttp-1.0

* Shogun N.T. Charge

** HNS/Nona Charge Capable of 450F available

*This product is protected by one or more of thefollowing patents: 5,542,480; 5,662,178; 5,638,901

Last Revised 05/2002

DescriptionDescriptionDescriptionDescriptionDescription

Owen's Spiral Shogun, when combined with the new Shogun N.T. Charge,posses the three most important features of an ideal perforator - Ideal Phas-ing, Deep Penetration, and High Shot Density

O.D. 1-11/16" 2-1/8" 2-1/2"Min. Restriction 1-25/32" 2-3/16" 2-19/32"Pressure Rating*Temperature**

20,000 psi375 F

2004 Owen Oil Tools All rights reserved

Owen Oil Tools

10

Shogun Spiral Strip* System,Shogun Spiral Strip* System,Shogun Spiral Strip* System,Shogun Spiral Strip* System,Shogun Spiral Strip* System,1-11/16", 2-1/8" & 2-1/2" O.D.1-11/16", 2-1/8" & 2-1/2" O.D.1-11/16", 2-1/8" & 2-1/2" O.D.1-11/16", 2-1/8" & 2-1/2" O.D.1-11/16", 2-1/8" & 2-1/2" O.D.Super Deep Penetrator & Big HoleSuper Deep Penetrator & Big HoleSuper Deep Penetrator & Big HoleSuper Deep Penetrator & Big HoleSuper Deep Penetrator & Big Hole

ttp-1.0(bk)

Item Part Number DescriptionSTP-1687-284 1-11/16" O.D., Firing Head, Spiral ShogunSTP-2125-284 2-1/8" O.D., Firing Head, Spiral ShogunSTP-2500-284 2-1/2" O.D., Firing Head, Spiral ShogunPUR-6000-005 Seizing CordSWG-0000-004 Seizing WireSTP-1687-209 1-11/16" Det Cord Protector Sleeve Assy. (w/ Retainer)STP-2125-209 2-1/8" & 2-1/2" Det Cord Protector Sleeve Assy. (w/ Retainer)

4 STP-2125-116 Det Cord Charge Clip, all sizes, included w/chargeSTP-1687-236HS Strip, 1-11/16" Shogun, 60/360, 4 shots/ft, 10' HSSTP-1687-232HS Strip, 1-11/16" Shogun, 40/360, 6 shots/ft, 10' HSSTP-2125-236HS Strip, 2-1/8" Shogun, 60/360, 4 shots/ft, 10' HSSTP-2125-232HS Strip, 2-1/8" Shogun, 40/360, 6 shots/ft, 10' HSSTP-2500-232S Strip, 2-1/2" Shogun, 60/360, 4 shots/ft, 10' S

6 STP-1687-084 3/8"-16 x 3/4" Bolt and Nut SetSTP-1687-288 Guide Nose, 1-11/16" Spiral ShogunSTP-2125-288 Guide Nose, 2-1/8" Spiral ShogunSTP-2500-288 Guide Nose, 2-1/2" Spiral ShogunSTP-1687-172 Heavy Guide Nose, 1-11/16" Spiral ShogunSTP-2125-172 Heavy Guide Nose, 2-1/8" Spiral ShogunSTP-2500-172 Heavy Guide Nose, 2-1/2" Spiral ShogunSTP-1687-229 2' Top Blank / Stiffener, 1-11/16" Spiral ShogunSTP-2125-229 2' Top Blank / Stiffener, 2-1/8" Spiral ShogunSTP-2500-229 2' Top Blank / Stiffener, 2-1/2" Spiral ShogunSTP-1687-013 3/8"-16 x 1" Bolt and Nut Set - For 1-11/16" & 2-1/8" Top SubSTP-1687-036 3/8"-16 x 1-1/4" Bolt and Nut Set - For 2-1/2" Top SubSTP-1687-185 Tandem, 1-11/16" Spiral ShogunSTP-2125-185 Tandem, 2-1/8" Spiral ShogunSTP-2500-185 Tandem, 2-1/2" Spiral ShogunSTP-2125-208 2-1/8" & 2-1/2" Det. Cord Retainer - for blank intervals on stripSTP-1687-208 1-11/16" Det. Cord Retainer - for blank intervals on stripAES-AS60030 Magnetic Decentralizer, For 1-11/16" Spiral ShogunDEC-2125-000 Magnetic Decentralizer, For 2-1/8" & 2-1/2" Spiral Shogun

13 AES-AS50029 Adapter Cablehead to expendableDET-0325-017 Det Cord, 80 Grain RDX, Nylon LSDET-0412-007 Det Cord, 80 Grain HMX, NylonDET-0412-003 Det Cord, HMX, Lead

STP-1687-401NTX Charge, 1-11/16" Spiral Shogun NTX, HMX, SDPSTP-1687-401NT Charge, 1-11/16" Spiral Shogun NT, HMX, SDPSTP-1687-401NB Charge, 1-11/16" Spiral Shogun NT, HMX, BHSTP-2125-401NTX Charge, 2-1/8" Spiral Shogun NTX, HMX, SDPSTP-2125-401NT Charge, 2-1/8" Spiral Shogun NT, HMX, SDPSTP-2125-401NB Charge, 2-1/8" Spiral Shogun NT, HMX, BHSTP-2500-401NT Charge, 2-1/2" Spiral Shogun NT, HMX, SDP

STP-2500-401NTXII Charge, 2-1/2" Spiral Shogun NTXII, HMX, SDPD DET-3050-022HE O-22HE Detonator-- STP-1687-162 Alignment Tool Kit for NT Charge-- MAN-STP1-001 Manual, Spiral Shogun System

1

2

3

5

7

8

9

10

11

12

A

C

Last Revised 07/2003

6

10

2D

1

13

12

9

7

6

5AC4

3

8

11

file:///F|/CATALOGS/freepoint_manual/freepoint%20manual%201.000/1inch_cover.htm

APPLIED ELECTRONIC SYSTEMS, INC.208 IDA

BROUSSARD, LA 70518TEL: 337-837-2016 / 800-523-6114

FAX: 337-837-2429

ONE INCH (1) FREEPOINT MANUAL

Since all Applied Electronic Systems freepoint tools operate the same, all tools should be run in the same manner.

NORMAL CONFIGURATION FOR RUNNING TOOLS

1. Cablehead2. Sinker bar(s) normally two(2) to three(3) bars3. Collar Locator4. Freepoint Slack Joint5. Freepoint Upper Bow Spring Section6. Freepoint Sensor Section7. Freepoint Lower Bow Spring Section8. Grounding Plug or Combination Sub for back-off.

Instructions in this supplement are for the specific equipment shown that is not included in the main Freepoint Back-off manual. For general operation and maintenance instructions refer to the main Freepoint Back-off manual.

file:///F|/CATALOGS/freepoint_manual/freepoint%20manual%201.000/1inch_cover.htm (1 of 2)6/24/2003 9:21:56 AM




String Shot - Back Off

This wireline conveyed pipe recovery tool uses a precise quantity of explosive detonating cord to produce shock waves.

The string shot-back off procedure involves applying left-hand torque to the pipe string at the neutral pipe weight (in neither tension nor compression). The string shot is then positioned at the pre-determined tool joint and detonated. The explosion produces much the same effect as an intense hammer blow and allows the joint to be unscrewed at the proper connection. The string shot-back off method has been improved through years of research and experience to increase operating efficiency without damaging the pipe string.

In order to make up a proper string shot, the following factors must be determined:

1. Pipe size, weight, and condition

2. Depth of back off

3. Borehole fluid type and weight

4. Well temperature

Factors 1, 2, and 3 are needed to determine the size of the string shot and factors 3 and 4 are needed for the selection of the proper fuses and detonating cord.

A string shot can be constructed that will readily run through an ID as small as 19.1mm. It can also be run in the annulus to back off the pipe from the outside.

Application

Back off pipe (inside and outside) Release stuck packers or fishing tools, such as an overshot Remove corrosion from pipe Reopen existing perforations Bump drill pipe loose in key seats (hard formations) Remove jet nozzles in drill bits to increase rate of circulation




Specification

Temperature Rating(C/48h): 260 Pressure Rating(MPa): 137.9

Backoff String Shot: The service uses a pre-determined quantity of detonating cord to deliver an explosive shock to stuck drill pipe, the objective being to allow recovery of the pipe. The shot is positioned at the pipe joint immediately above the freepoint determined by the FPT tool. It is detonated with the pipe joint at neutral weight, and with uncoupling torque applied at the surface. The size of the shot is calculated according to the pipe size and weight, the depth of the stuck pipe and the nature of the wellbore fluid. String shots are also used to free drill pipe from keyseats, to remove corrosion from pipe (for example, prior to the use of chemical cutters) and to reopen existing perforations.

05/01REV05/04 9-2

TOOL SIZE (ANCHOR & SEV HEAD)

MAX. EXTENSION OF ANCHOR SLIPS OD (INCH) ID (INCH)

W EIGHT POUND/FOOT

1 3/8 1.80 1.90 1.500 - 1.650 2.40 - 3.64

2 1/16 1.670 - 1.751 3.25 - 3.40

2 3/8 1.703 - 1.995 4.70 - 7.70

1 9/16 2.10 2 3/8 1.853 - 1.995 4.70 - 6.20

1 11/16 2.20 2 3/8 1.939 - 1.995 4.70 - 5.30

1 3/4 2.50 2 7/8 2.059 - 2.441 6.50 - 10.70

1 7/8 2.55 2 7/8 2.059 - 2.441 6.50 - 10.70

2 " 2.58 2 7/8 2.195 - 2.441 6.50 - 9.50

2 1/8 2.60 2 7/8 2.323 - 2.441 6.50 - 7.90

2" E. R. 2.85 3 1/2 2.480 - 2.750 12.95 - 16.70

2 1/8 E. R. 3.10 3 1/2 2.480 - 2.992 9.30 - 16.70

2 3/16 3.10 3 1/2 2.480 - 2.992 9.30 - 16.70

2 1/4 3.15 3 1/2 2.602 - 2.992 9.30 - 15.50

2 3/8 3.25 3 1/2 2.602 - 3.068 7.70 - 15.50

*2 5/8 3.35 3 1/2 2.922 - 3.068 7.70 - 10.30

*2 7/8 3.65 4 3.240 - 3.476 11.00 - 15.70

*3 1/8 3.92 4 3.340 - 3.548 9.50 - 14.00

*3 1/4 4.04 4 1/2 3.640 - 3.958 12.60 - 20.00

*3 3/8 4.16 4 1/2 3.697 - 4.000 11.60 - 17.70

*3 1/2 4.28 4 1/2 3.826 - 4.090 9.50 - 15.50

*3 5/8 4.40 4 1/2 3.920 - 4.090 9.50 - 13.50

*3 7/8 4.68 5 4.154 - 4.408 15.00 - 21.00

*4 " 4.80 5 4.276 - 4.560 11.50 - 19.50

*4 3/16 4.92 5 1/2 4.548 - 4.778 20.00 - 26.00

*4 7/16 5.14 5 1/2 4.670 - 4.950 15.50 - 23.00

*4 9/16 5.14 5 1/2 4.892 - 5.044 13.00 - 17.00

5 1/2 6.50 7 6.004 - 6.214 28.00 - 35.00

5 3/4 6.50 7 6.276 - 6.456 20.00 - 26.00

6 3/8 7.37 7 5/8 6.765 - 7.125 20.00 - 33.70

7 1/2 8.5 8 5/8 7.725 - 8.017 24.00 - 40.00

SELECTION GUIDE F/ TUBING, CASING & DRILL PIPE CHEMICAL CUTTER

TOOL SPECIFICATIONS (IN) TUBING SPECIFICATIONS

1 1/2 2.04

0501REV0104

CIbarra5 1/2 6.50 7 6.004 - 6.214 28.00 - 35.00

CIbarra(ANCHOR &SEV HEAD)ANCHOR SLIPS OD(INCH) ID (INCH) WEIGHTPOUND/FOOT

CIbarraTOOL SIZEMAX. EXTENSION OF

CIbarraTOOL SPECIFICATIONS (IN) TUBING SPECIFICATIONS

12/01REV05/04 10-2

1101REV0104TOOL SIZE CYLINDER CATALYST(ANCHOR & QTY & SIZE SIZESEV HEAD) OD WT: #/FT 0-5 KPSI 5-10 KPSI

1 3/8 1.9 2.40-3.64 1 - 1 3/8 x 72 8 X 9/16 9 X 9/16 #5

2 1/16 3.25-3.40 1 - 1 3/8 x 72 8.5 X 9/16 9.5 X 9/16 #6

2 3/8 4.70-7.70 1 - 1 3/8 x 72 8.5 X 9/16 9.5 X 9/16 #6

1 9/16 2 3/8 4.70-6.20 1 - 1 3/8 x 72 8.5 X 9/16 9.5 X 9/16 #6

1 - 1 11/16 x 48 8.5 X 9/16 9.5 X 9/16 #6

1 - 1 11/16 x 60 9 X 9/16 10 X 9/16 #6

1 3/4 2 7/8 6.50-10.70 1 - 1 11/16 x 72 9.5 X 9/16 10.5 X 9/16 #6

1 7/8 2 7/8 6.50-10.70 1 - 1 11/16 x 72 9.5 X 9/16 10.5 X 9/16 #6

2 2 7/8 6.50-9.50 1 - 1 11/16 x 72 9.5 X 9/16 10.5 X 9/16 #6

1 - 1 11/16 x 48 8.5 X 9/16 9.5 X 9/16 #6

1 - 1 11/16 x 60 9 X 9/16 10 X 9/16 #6

2" E. R. 3 1/2 12.95-16.70 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

2 1/8 E. R. 3 1/2 9.30-16.70 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

2 3/16 3 1/2 9.30-16.70 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

2 1/4 3 1/2 9.30-15.50 1 - 2 x 72 12 X 9/16 13 X 9/16 #10

7.70-10.30 1 - 2 x 60 11 X 9/16 12 X 9/16 #10

12.95-15.50 1 - 2 x 72 12 X 9/16 13 X 9/16 #10

2 5/8 3 1/2 7.70-10.30 1 - 1 11/16 x 72 10 X 9/16 11 X 9/16 #10

2 7/8 4 11.00-15.70 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

3 1/8 4 9.50-14.00 1 - 2 x 72 12 X 9/16 13 X 9/16 #10

3 1/4 4 1/2 12.60-20.00 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

3 3/8 4 1/2 11.60-17.70 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

3 1/2 4 1/2 9.50-15.50 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

3 5/8 4 1/2 9.50-13.50 1 - 2 x 72 12 X 9/16 13 X 9/16 #10

3 7/8 5 15.00-21.00 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

11.50-15.00 1 - 2 x 72 12 X 9/16 13 X 9/16 #10

16.25-19.50 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

4 3/16 5 1/2 20.00-26.00 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

4 7/16 5 1/2 15.50-23.00 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

13.00-15.00 1 - 2 x 72 12 X 9/16 13 X 9/16 #10

15.50-17.00 2 - 2 x 48 14 X 9/16 15 X 9/16 #10

5 1/2 7 28.00-35.00 2 - 2 x 72 12.5 X 3/4 13.5 X 3/4 #12

5 3/4 7 20.00-26.00 2 - 2 x 60 11.5 X 3/4 12.5 X 3/4 #12

6 3/8 7 5/8 20.00-33.70 2 - 2 x 72 12.5 X 3/4 13.5 X 3/4 #12

7 1/2 8 5/8 24.00-40.00 2 - 2 x 72 12.5 X 3/4 13.5 X 3/4 #12

NOTE: THE GRAIN LENGTH MUST BE INCREASED BY 1" WHEN ANY OF THE FOLLOWING CONFIGURATIONS ARE USED: TANDEM ANCHORS, ADJUSTABLE TOP CENTRALIZER, EXTENSION SPACER

2 3/8 3 1/2

1 1/2

1 11/16

GAS GENERATOR GRAIN / CHEMICAL CYLINDER CHARTF/ 1 3/8 - 7 1/2 OD TOOLS

2 1/8 2 7/8 6.50-7.90

TUBING GRAIN LENGTH (INCH) X GRAIN OD (INCH)VS BHP (KPSI)

4.70-5.302 3/8

4 9/16 5 1/2

4 5

CIbarra5 1/2 7 28.00-35.00 2 - 2 x 72 12.5 X 3/4 13.5 X 3/4 #12

CIbarraTOOL SIZE CYLINDER CATALYST(ANCHOR & QTY & SIZE SIZESEV HEAD) OD WT: #/FT 0-5 KPSI 5-10 KPSITUBING GRAIN LENGTH (INCH) X GRAIN OD (INCH)VS BHP (KPSI)

26-1010/02REV05/04




DST




HERRAMIENTAS DE SUBSUELO Las herramientas de subsuelo permiten efectuar la prueba del pozo de manera segura y eficiente, permitiendo obtener informacin precisa y confiable de los fluidos producidos y propiedades del yacimiento, entre otros. Mediante el uso de las herramientas de subsuelo DST se pueden realizar cierres en fondo, obtener muestras limpias de los fluidos de formacin, facilitar las operaciones de completamiento y caoneo, etc. La sarta bsica de DST incluye: Empaque de Prueba, Vlvula de Cierre en Fondo, Vlvula de Circulacin, Vlvula de Reversa, Registradores de Presin y Temperatura y dems herramientas adicionales. 1. Vertical Shock Absorber REFERENCIA TRIPOINT FABRICA USA DESCRIPCION VERTICAL O.D. 5.000 in I.D. 2.370 in LONGITUD 3.598 ft AMBIENTE H2S / CO2 TEMPERATURA 350 F (Mx.) CONEXIONES 3 API EUE BOX x PIN MAX. PRESION DIFERENCIAL 10,000 psi TENSION MXIMA 140,000 lbs CARGA MXIMA 50,000 lbs Caractersticas: Protege los registradores de presin y temperatura de la sarta de DST del

impacto vertical transmitido a travs de la sarta de prueba por el caoneo con TCP.

Protege otros elementos sensibles dentro de la sarta de DST. Se corre normalmente debajo del empaque y siempre se ubica entre el memory

carrier y los caones.




2. Radial Shock Absorber REFERENCIA TRIPOINT FABRICA USA DESCRIPCION RADIAL O.D. 5.000 in I.D. 2.370 in LONGITUD 3.598 ft AMBIENTE H2S / CO2 TEMPERATURA 350 F (Mx.) CONEXIONES 3 API EUE BOX x PIN MAX. PRESION DIFERENCIAL 10,000 psi Caractersticas: Protege los registradores de presin y temperatura de la sarta de DST del

impacto radial transmitido a travs de la sarta de prueba por el caoneo con TCP (a travs de toda la circunferencia de la sarta).

Protege otros elementos sensibles dentro de la sarta de DST. 3. Empaque de Peso para Revestimiento de 9-5/8 REFERENCIA JS MARCA EXPRO GROUP FABRICA USA DESCRIPCION 9-5/8 Mecnico O.D. 8.218 in I.D. 3.000 in LONGITUD 8.500 ft AMBIENTE H2S / CO2 TEMPERATURA - 22 F / 425 F CONEXIONES 3-1/2 EUE 8RD MAX. PRESION HIDROST. 15,000 psi MAX. PRESION INTERNA 15,000 psi MAX. PRESION EXTERNA 15,000 psi Caractersticas: Para revestimiento de 9 5/8, 47 53.3 lb/ft, P-110.




Presenta By-Pass interno para permitir el flujo libre de fluidos a travs del empaque durante la corrida, recuperacin y circulacin.

Ideal para altas presiones diferenciales. Se sienta rotando a la derecha 1/3 de vuelta y aplicando peso. Se recupera levantando la tubera o la sarta, lo cual abre el by-pass para

igualizar la presin arriba y abajo del empaque. Cauchos resistentes a 220 F. Doble agarre. 4. Empaque de Peso para Revestimiento de 7 REFERENCIA JS MARCA EXPRO GROUP FABRICA USA DESCRIPCION 7 Mecnico O.D. 5.812 in I.D. 2.375 in LONGITUD 8.500 ft AMBIENTE H2S / CO2 TEMPERATURA - 22 F / 425 F CONEXIONES 2-7/8 EUE 8RD MAX. PRESION HIDROST. 15,000 psi MAX. PRESION INTERNA 15,000 psi MAX. PRESION EXTERNA 15,000 psi Caractersticas: Para revestimiento de 7, 29 32 lb/ft, P-110. Presenta By-Pass interno para permitir el flujo libre de fluidos a travs del

empaque durante la corrida, recuperacin y circulacin. Ideal para altas presiones diferenciales. Se sienta rotando a la derecha 1/3 de vuelta y aplicando peso. Se recupera levantando la tubera o la sarta, lo cual abre el by-pass para

igualizar la presin arriba y abajo del empaque. Cauchos resistentes a 220 F. Doble agarre.




5. Junta de Seguridad MARCA BOWEN OIL TOOLS FABRICA USA TAMAO 3-1/2 API IF O.D. 4-3/4 I.D. 2-11/16 LONGITUD 2.500 ft RATING DE TENSION 340,000 lbs AMBIENTE H2S / CO2 TEMPERATURA - 22 F / 425 F CONEXIONES 3-1/2 API IF BOX x PIN MAX. PRESION HIDROST. 15,000 psi MAX. PRESION INTERNA 15,000 psi MAX. PRESION EXTERNA 15,000 psi Caractersticas: Es una herramienta de back-off de emergencia. La junta de seguridad permite

una rpida liberacin de la sarta de prueba, en caso de que el empaque o algn elemento debajo de l, queden pegados en el pozo.

Se corre inmediatamente encima del empaque de tal forma que el mayor nmero de herramientas pueda ser recuperado.

Se desenrosca aplicando torque hacia la izquierda. Presenta O-rings en las roscas para sello contra presiones internas y externas. 6. Martillo Hidrulico REFERENCIA ALPINE - WEATHERFORD FABRICA CANADA DESCRIPCION TOTAL STROKE 10 O.D. 4.500 in I.D. 2.380 in LONGITUD 6.500 ft CAPACIDAD DE GOLPE 70,000 lbs hacia arriba AMBIENTE H2S / CO2 TEMPERATURA - 22 F / 425 F CONEXIONES 3-1/2 API IF BOX x PIN MAX. PRESION HIDROST. 15,000 psi MAX. PRESION INTERNA 15,000 psi




MAX. PRESION EXTERNA 15,000 psi Caractersticas: Mediante su accin de martilleo, se usa para liberar la sarta atascada en el pozo. Herramienta con tiempo regulable, para transmitir un rpido y fuerte movimiento

de la sarta de prueba. Simple de ensamblar y fcil de operar. No interfiere con la operacin de las herramientas de prueba. Permite al operador controlar fcilmente la intensidad de la accin de martilleo. 7. Muestreador de Fondo REFERENCIA BAKER FABRICA USA O.D. 5.000 in I.D. 2.250 in CAPACIDAD 1,200 cc AMBIENTE H2S / CO2 CONEXIONES 3-1/2 API IF BOX x PIN MAX. PRESION HIDROST. 10,000 psi MAX. PRESION INTERNA 10,000 psi MAX. PRESION EXTERNA 10,000 psi Caractersticas: Atrapa una muestra del fluido del pozo, sin necesidad de cerrar el pozo. Esta

muestra es guardada en el espacio anular de la herramienta hasta que sale a superficie y se recupera.

Recupera muestras del pozo en cualquier momento de la operacin. Permanece full open una vez la herramienta atrapa la muestra. 8. Vlvula para Prueba de Tubera (Single Cycle Ball Valve) REFERENCIA TRIPOINT FABRICA USA O.D. 5.000 in I.D. 2.250 in




LONGITUD 68.30 in RANGO DE TENSION 380,000 lbs AMBIENTE H2S y CO2 TEMPERATURA - 22 F / 350 F CONEXIONES 3-1/2" API IF MAX. PRESION HIDROSTATICA 10,000 psi MAX. PRESION INTERNA 10,000 psi MAX. PRESION EXTERNA 10,000 psi Caractersticas: Vlvula de bola controlada por presin anular. Pasaje pleno. Diseada para usar durante pruebas simples de cased hole y

operaciones de caoneo, donde solamente una fase de flujo y cierre es requerida.

Con sistema de seguridad que permite dejar en posicin la vlvula abierta, una vez accionada.

Operada por un pistn diferencial, controlado por presin anular. Se puede bajar en posicin abierta o cerrada, dependiendo de los requerimientos

operacionales. 9. Vlvula de Flujo Mltiple (Tester Valve) REFERENCIA TRIPOINT FABRICA USA O.D. 5.000 in I.D. 2.250 in LONGITUD 21 ft CONEXIONES 3-1/2 API IF RANGO DE TENSION 340,000 lbs AMBIENTE H2S y CO2 TEMPERATURA 350 F RANGO PRES. DIFERENCIAL CONTRA LA BOLA 15,000 psi RANGO PRES. DIFERENCIAL ANULAR/TUBING 15,000 psi PRES. HIDROSTATICA INICIAL 15,000 psi MAX. PRESION HIDROSTATICA 17,500 psi




Caractersticas: Vlvula de bola de ciclo continuo, de pasaje pleno. Accionada por presin anular. Para cierre en fondo lo ms cerca posible de las perforaciones. Elimina el efecto de almacenamiento de pozo. Puede abrirse y cerrarse a distintos tiempos, cuantas veces lo requiera la prueba. Reduce tiempos de prueba. Permite operaciones de estimulacin tales como acidificacin y fracturamiento. 10. Vlvula de Circulacin Mltiple (Circulating Valve) REFERENCIA TRIPOINT FABRICA USA O.D. 5.000 in I.D. 2.250 in LONGITUD 7.770 in CONEXIONES 3-1/2 API IF RANGO DE TENSION 340,000 lbs AMBIENTE H2S y CO2 TEMPERATURA SERVICIO 350 F RANGO DE PRESION 15,000 psi MAX. RATA DE BOMBEO 4.0 Bbls/min Caractersticas: Vlvula de circulacin mltiple (directa y reversa) de pasaje pleno. Herramienta de presin diferencial. Usa la presin diferencial entre el tubing y el

anular. Cinco posiciones cerrada, una posicin reversa y una de circulacin. Depende de una baja presin diferencial (300 psi). Permite operaciones de estimulacin y posicionamiento de fluidos tales como

diesel, cidos, nitrgeno y otros. 11. Vlvula de Circulacin de Disco de Ruptura (Reversing Valve) REFERENCIA ALPINE - WEATHERFORD FABRICA CANADA




O.D. 5.000 in I.D. 2.400 in LONGITUD 2.900 ft RATING DE TENSION 424.000 lbs AMBIENTE H2S y CO2 TEMPERATURA SERVICIO - 22 F / 350 F CONEXIONES 3-1/2 API IF MX. PRESION HIDROSTATICA 10,000 psi MX. PRESION INTERNA 10,000 psi MAX. PRESION EXTERNA 10,000 psi DESCRIPCION 1 Aperture Rupture Disc Caractersticas: Se activa despus de romperse un disco de ruptura previamente seleccionado a

cierta presin anular. Al romperse el disco, la herramienta queda permanentemente abierta. Permite circular el pozo antes de sacar tubera, lo que elimina los derrames y la

contaminacin con crudo. Puede tenerse como vlvula de backup de la vlvula de circulacin en caso de

contingencia. 12. Sub Radiactivo No. de Parte TCP-0100-350 Referencia OWEN OIL TOOLS Fabrica USA O.D. 2.875 in 5.000 in I.D. 2.400 in Longitud 2.900 ft Conexin 2 7/8 EUE, 3 IF Caractersticas: Es empleado en el sistema Tubing Conveyed Perforating TCP. Posicionado a una distancia medida por encima del tope del can. Se emplea para correlacionar la posicin de los caones con los registros

tomados en hueco abierto.




13.l Slip Joints REFERENCIA TRIPOINT FABRICA USA O.D. 5.000 in I.D. 2.250 in LONGITUD CERRRADO 21.60 ft LONGITUD ABIERTO 26.60 ft TENSION 320.000 LB AMBIENTE H2S / CO2 TEMPERATURA SERVICIO 400 F CONEXIONES 3 API IF box x pin MAX. PRESIN HIDROSTATICA 15,000 psi MAX. PRESIN INTERNA 15,000 psi MAX. PRESIN EXTERNA 15,000 psi Caractersticas: Permiten el movimiento vertical de la sarta de prueba sin afectar el

posicionamiento de las herramientas por cambios de temperatura, presin y peso de la sarta.

DOWNHOLE TOOLS

JS-2 Retrievable Casing Packer

The JS-2 Retrievable Casing Packer is a full-opening, set-down type hook-wallpacker that is applicable for use in a variety of well treating, testing, and TubingConveyed Perforating operations. The packers are available in 4-1/2 through9-5/8 casing sizes and feature a large internal bypass that provides a freeflow of fluids through the packer during running, retrieving, and circulating.This packer is ideal for use when high differential pressures from below thepacker are anticipated and utilizes hydraulically-actuated button-type slips toanchor the packer against upward movement.

Setting the JS-2 is accomplished by rotating 1/3 right hand turn at the tool andsetting weight down. This one operation sets the slips, energizes the packingelements, and closes the bypass. Retrieval is accomplished by straight pick-up of the tubing or workstring that opens the bypass to equalize pressureabove and below the packer. Continued pick-up will retract the slips and allowthe packing elements to relax. The automatic J system will engage and allowthe packer to be retrieved or moved downhole and be reset.

Specifications

4.50 5.00 5.50 5.50 5.50

Casing Weight 9.5-13.5# 15-18# 20-23# 15.5-20# 13-15.5#Max. O.D. 3.771 4.125 4.570 4.641 4.781I.D. in. 1.812 1.812 1.875 1.875 1.875Connections 2-3/8 EU 2-3/8 EU 2-3/8 EU 2-3/8 EU 2-3/8 EU

8RD 8RD 8RD 8RD 8RD

7.00 7.00 7.00 7.00 7.00

Casing Weight 38# 32-35# 26-29# 20-26# 17-20#Max. O.D. 5.656 5.812 5.968 6.078 6.266I.D. 2.375 2.375 2.375 2.375 2.375Connections 2-7/8 EU 2-7/8 EU 2-7/8 EU 2-7/8 EU 2-7/8 EU

8RD 8RD 8RD 8RD 8RD

7.625 7.625 7.625

Casing Weight 33.7-39# 24-29.7# 20-24#Max. O.D. 6.453 6.672 6.812I.D. 2.375 2.375 2.375Connections 2-7/8 EU 2-7/8 EU 2-7/8 EU

8RD 8RD 8RD

9.625 9.625 9.625

Casing Weight 47-53.5# 40-47# 29.3-36#Max. O.D. 8.218 8.437 8.593I.D. 3.00 3.00 3.00Connections 3-1/2 EU 3-1/2 EU 3-1/2 EU

8RD 8RD 8RD

Note: The most common sizes and specifications are depicted above. Other sizes are available upon request.

Internal Bypass

HydraulicHold Down

Slips

PackingElements

Slips

Drag Blocks

TRITON TOOLS

TRITON Tester Valve (TTV)

The TRITON Tester Valve (TTV) is a continuous-cycle ball valve used to shut-in a well as close to the perforations as possible. It may be functioned openand closed as many times as required by the test conditions. Typical uses forthe tester valve are:

Bottom-hole shut-in during drill stem testing to virtually remove thewellbore effects from buildup / fall-off test, thereby getting cleaner, easier-to-analyze data and significantly reducing the required shut-intimes, especially for tight gas formations.

Safety shut-in valve for any situation where the workstring or treeconnection develops an integrity problem.

Fluid-loss control tool when formation pressures are seriously under-estimated and the formation is taking massive amounts of expensivecompletion fluid. Used in conjunction with the Multi-Function CirculatingValve to adjust fluid weight, optimize well control and minimize formationdamage.

The TTV is annulus pressure operated and has a single ball with seats oneither side so that pressure integrity may be maintained from above or below.Hydrostatic pressure compensation is accomplished by a nitrogen chamberand reference section that allows annulus pressure (fluid) to enter a port belowa balance piston on the way in the hole. This port is closed (and the hydrostaticreference trapped) when weight is stacked off on the tool, usually when thepacker is set.

Specifications Standard Slimhole

O.D. 5.00 3.125

I.D. 2.25 1.125

Length 21.0 21.0

Max. Temperature 350 F 350 F

Metals Inconel or K500 for Inconel or K500 forDynamic Areas Dynamic Areas4100 Series H2S Rated 4100 Series H2S RatedConnector Subs Connector Subs

Tensile Strength 340,000 lbs. 120,000 lbs.

End Connections 3-1/2 IF or 3-1/2 PH6 As required by client

Actuating Pressure Adjustable, 1200-2000 PSI Adjustable, 1200-2000 PSI(Annulus) (Normally 1800 lbs.) (Normally 1800 lbs.)

Pressure RatingsDifferential Against Ball 15,000 PSI 15,000 PSIMax. Opening Dif. 7,000 PSI 7,000 PSIDifferential Ann/Tub 15,000 PSI 15,000 PSIInitial Hydrostatic 15,000 PSI 15,000 PSIMax. Hydrostatic 17,500 PSI 17,500 PSI

Upper Piston

Power Spring

N2 Injector Port

N2 Chamber

Balance Piston

Connector

AnnulusPressure Port

HydrostaticReference Port

Ball Valve

TRITON TOOLS

TRITON Circulating Valve (TCV)

The TRITON Circulating Valve (TCV) is a differential pressure tool with 5closed positions (3 for Slimhole), 1 reverse position, and 1 circulating position.The tool can cycle through this sequence as many times as is required by thewell program. The TCV is used in conjunction with the Tester Valve for almostall applications. Typical uses for the circulating valve are:

Reverse out tubing contents to remove hydrocarbons and debris fromthe workstring while the formation is isolated by the closed tester valve.

Spot lighter weight fluid (including nitrogen) to create or increase anunderbalance to formation in order to surge perforations or establish flowin a drill stem test.

Efficiently spot viscous pills to cure fluid loss to formation. (Spot pill tothe circulating ports close TCV, then open the ball valve to allow the pillto move to the perforations)

The TCV cycles using tubing / annulus differential pressure to move the portedmandrel up (annulus > tubing) and down (tubing > annulus). This up and downmotion causes the index sleeve to rotate around the mandrel on the indexpins. After the specified number of limited movements (closed positions), themandrel is allowed to move into a long slot that allows the ported mandrel toline up with reversing ports. Fluid flow from the annulus to the tubing may nowcommence. When the operator is finished with the reverse position, pressureis applied down the tubing, the mandrel travels up into a second long slot, andthe ported mandrel is aligned with the circulating ports. When the operator isfinished circulating, annulus pressure is applied to move the mandrel into the1st closed position.

Please notice that there is no rate dependency to cycle the tool; everything isdone with a low differential pressure (300 psi). As long as the tool has apositive differential in the direction of flow, the tool will remain open; to movethe tool to the next position, a 300 psi differential pressure is applied from theopposite direction.

Specifications Standard Slimhole

Pressure Ratings 15,000 PSI 15,000 PSI

O.D. 5.00 3.125

I.D. 2.25 1.125

Length 7.77 10.0

Max. Temperature 350 F 350 F

Metals Iconel or K500 for Iconel or K500 forDynamic Areas Dynamic Areas4100 Series H2S Rated 4100 Series H2S RatedConnector Subs Connector Subs

Tensile Strength 340,000 lbs. 120,000 lbs.

End Connections 3-1/2 IF As required by client

Actuating Pressure 300 PSI - tubing 300 PSI - tubing(Differential) 300 PSI - Annulus 300 PSI - Annulus

Max. Pump Rate 4.0 bbl/min 2.5 bbl/min

Indexing Mandrel

Guide Sleeve

AnnularCirculation

Port

ReverseCirculation

Port

DOWNHOLE TOOLS

Single Cycle Ball Valve

The Single Cycle Ball Valve is an annular pressure-controlled ball valve and isdesigned to be used during simple cased hole testing and perforatingoperations, where only one flowing and one shut-in phase is required.

The Single Cycle Ball Valve is operated by a differential piston, controlled byannulus pressure. Annulus hydrostatic pressure at tool depth, plus desiredoperating pressure, is calculated prior to the Ball Valve being run downhole toensure the correct selection of rupture discs.

The Single Cycle Ball Valve is run in the hole in either the open or closedposition, depending on operational requirements. When the tool is required tofunction, pressure is applied to the corresponding rupture disc which willrupture causing the tool to cycle.

The Single Cycle Ball Valve is fully-balanced to tubing pressure and will remain in the position to which it was last cycled. By having this ability, the pressureon the annulus can be decreased or returned to hydrostatic.

The Single Cycle Ball Valve can be run in conjunction with other annularpressure operated downhole tools and has only to be setup to operate at thecustomers required pressures.

Primary Uses Fluid Loss Control Surge Tool

Specifications

O.D. 5.00"

I.D. 2.25"

Length 68.3"

Internal Pressure 10,000 PSI

Tensile Rating 380,000 lbs.

Max. Differential Opening Pressure 5,000 PSIConnections 3-1/2" API IF

Valve OpenRupture Disc

UpperOperating

Piston

Ball

LowerOperating

Piston

Valve CloseRupture Disc

gr_scintillation.pdf3 1/8 in (7.94 cm) Logging Scintillation Gamma Ray3 1/8 in (7.94 cm) Perforating Scintillation Gamma Ray with CCL

FREE POINT.pdf1inch_cover.pdf1inch_cover.pdfLocal Diskfile:///F|/CATALOGS/freepoint_manual/freepoint%20manual%201.000/1inch_cover.htm

PG 11-1.pdfLocal Diskfile:///C|/Documents%20and%20Settings/buster/Desktop/pg.txt

ccls.pdf1 in (2.54 cm) Logging CCL1 3/8 in (3.49 cm) Logging CCL1 11/16 in (4.29 cm) Logging CCL2 3/4 in (6.99 cm) Logging CCL3 1/8 in (7.94 cm) Logging CCL1 in (2.54 cm) Passive Shooting CCL1 3/8 in (3.49 cm) Passive Shooting CCL1 7/16 in (3.65 cm) Passive Shooting CCL1 11/16 in (4.29 cm) Passive Shooting CCL2 in (5.08 cm) Passive Shooting CCL2 1/8 in (5.40 cm) Passive Shooting CCL2 3/4 in (6.99 cm) Passive Shooting CCL3 1/8 in (7.94 cm) Passive Shooting CCL4 1/2 in (11.43 cm) Passive Shooting CCL

6 - EQUIPOS

Documents

Transcript of 6 - EQUIPOS