! MOP is the primary Source , File for only Pre & Post check !!2G - PRE_CHECK !! ============================================================================================================= !! PRE_2G !i) Scripts Checking:a). Check all the scripts present in the folder - Cell,chgr,gprs and Excel file.b). Check the type of activity (Helice or No_Helice) in Ticket and Excel.c). Open cell script , check all the cells(GSM+ are present or not(as per no. of sectors in excel)check all the parameters are filled, there should not be any blank. d). Open chgr script , check for all cells number of DCHNO is equal to Configuration per sector.e). Open Gprs script , check all the cells available or not?.Note : Same applicacle for Orange - if any. Any mismatch found in script & excel need to confirm with Radio team for each parameter.ii) BSC:a). Open BSC - can be found from Excelb). Check the cells are already defined -- RLDEP:CELL=; (if present Check CGI,BCCHNO,BSIC) c). check the number of frequencies -- RLCFP:CELL=; (number of DCHNOs == Configuration)d). Check TG is free -- RXMOP:MO=RXOTG-,subord; (TG-no from Excel) if present verify TRX configuration as per excel.iii) If Cells and TG not available , start loading CNA & MO. Note : Need to check failed commands in Update log , and clarify with Radio team for the parameters. ( RLVAR , RLSTC - commands failed -- acceptable)! ============================================================================================================= !! SWAP_2G ! i) Scripts Checking:a). Check all the scripts present in the folder - (UCELL, 2G2G , 2G3G neighboring file , Old cell deletion file - CNA) & ( Borroda & creado .xml files - 3G)b). Check the type of activity (Helice or No_Helice) in Ticket and Excel.Note : Same applicacle for Orange - if any. Any mismatch found in script & excel need to confirm with Radio team for each parameter.ii) BSC:a). Open old BSC & Cell - can be found from Old cell deletion file b). Check configuration and cell status in old BSC -- RLDEP:CELL=; - RXMSP:MO=RXOTG-,subord; - RXMOP:MO=RXOTG-; - for all cellsc). Check the cells definition in new BSC -- RLDEP:CELL=; (Check CGI,BCCHNO,BSIC values) - for all cells as per excel data. d). check the number of frequencies -- RLCFP:CELL=; (number of DCHNOs == Configuration) - for all cells as per excel data.e). Check TG -- RXMOP:MO=RXOTG-,subord; (TG-no from Excel) - verify TRX configuration as per excel. ! ============================================================================================================= !! ============================================================================================================= ! ! Post Ceheck !rldep:cell=cell1; ! Check CGI , BCCHNO , BSIC - should be present !rlcfp:cell=cell1; ! (number of DCHNOs == Configuration) - for all cells as per excel data !rlslp:cell=cell1; ! LVA should be set as per configuration , ACL should be BCCH=A1 , SDCCH=A2 , TCH=A3 )!Note :- In Pre_2G ACTIVE=YES only for Zone2 (RLSLI:CELL=; !! In 2G_900 ACTIVE=YES for all zones ! rlcpp:cell=cell1; ! check cell power !rlcrp:cell=cell1; ! ICMBAND = 1 & 2 acceptable and can see Usage !rlnrp:cell=cell1,cellr=all,nodata; ! 2G-2G Neighboring !rlnrp:cell=cell1,cellr=all,utran; ! 2G-3G Neighboring !RXTCP:MOTY=RXOTG,CELL=cell1; ! To find TG from known cell !RXMSP:MO=RXOTG-xx,SUBORD; ! MO Status !RXMOP:MO=RXOTG-xx,SUBORD; ! Mo data !RXCDP:MO=RXOTG-xx; ! MO config. !! To find MO config. !RXMOP:MO=RXOTX-xx-0;RXMOP:MO=RXOTX-xx-1;RXMOP:MO=RXOTX-xx-2;RXMOP:MO=RXOTX-xx-3;RXMOP:MO=RXOTX-xx-4;RXMOP:MO=RXOTX-xx-5;RXMOP:MO=RXOTX-xx-6;RXMOP:MO=RXOTX-xx-7;RXMOP:MO=RXOTX-xx-8;RXMOP:MO=RXOTX-xx-9;RXMOP:MO=RXOTX-xx-10;RXMOP:MO=RXOTX-xx-11;RRSGP:SCGR=; ! To find PSTU name!RRPTP:PSTU=XXXXXX; ! PSTU Status !! intenal Alarm !RXMFP:MO=RXOTG-xx,SUBORD,FAULTY;RXASP:MO=RXOTG-xx;! External Alarm !allip:acl=a1;! ============================================================================================================= !! ============================================================================================================= !! 3G !! 3G - PRE_CHECK ! i) Get U2100 & U900 site name from Maxplank Export a). case 1 - U2100 & U900 are in same Iub , So we have single node-B name b). case 2 - U2100 & U900 are in different Iub , So we have two node-B name c). case 3 - U2100 with Orange RNC & U900 with Vodafone , here U900 node-B name & Orange node-B name will be present in the sheet.ii) Login to Node-B & RNC and check Cabinet type , configuration , alarm in U2100 ! Node-B !altst secst carcabxst plugget iubget . dualstackget . cellidget 0get 6license serverget 10acc iproutingtable listrouteslst ipsyncrefget ipsyncrefget . ipsyncrefget nodeBlst carlst secst auxlst ethst ppget . autoconfigurationallowedget txd hs|eulget . steeredHsAllocationget . hsCodeResourceIdget . maxNumEulUsersget . maxtotalget . maxNumHsdpaUsersget sectorlst supget Equipment=1,HwUnit=SUP-1,ControlPort=get . txbraget . radioblst Equipment=1,HwUnit=SUP-1,AlarmPort=get . fqget . maxDlPowerCapabilityget . antennasuplh ru fui get vswraltst secst carcvlscvms Pre_Actget . gpsoutget . buildget . txbranchget . mixget . bandget . eultdsget radio noget . transportkget allq! RNC ! alt lst 0206GI get Iub_0206GI lst 0206GI|GI05FU|025212 alt | egrep '(0206GI|GI05FU|025212)' strt pmr -m .5 -r 14,15,16,17,23 | egrep -i '(0206GI|GI05FU|025212)' get 0206GI|GI05FU|025212 primaryCpichPower get 0206GI|GI05FU|025212 maximumTransmissionPower get 0206GI|GI05FU|025212 PrimaryScramblingCode cedr | egrep '(0206GI|GI05FU|025212)' q!!!! DUW-41 !!!!!!!!!!!!!!!lset 17050 17126 74342 74398 75203 75211 pathlossThresholdEulTti2 127!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Post Check !Get . antennasup -- this command is used to check the alarm supervision of the antennas and it must be set to 48 in both branches A and BGet . txbranch -- this command is used to check how many branches that the Radio Units has, for U2100 all sectors must have 2 tx branchesGet . output -- this command is used to check the Total Output Power of the Radio Units, you have to ask to the FE if the Radio Units installed are of 80 or 120Watts, if the Radio Units Installed are of 80Watts the Output power must be set to 40Watts on every Sectors, but if the Radio Unit Installed are of 120Watts the Output power must be set to 60Watts on every Sectors.RRUS11B1 = 80Watts Radio Units ---> Total Output Power must be set to 40RRUS12B1 = 120Watts Radio Units ----> Total Output Power must be set to 60Get . mixedmode -- this command is used to check if someone of the sector has configured the feature of mixedmode, usually this feature is activated on the U900 sectorsGet . gpsout -- this command is used to check that the primary DUW is connected and synchronized with the DUG of 2G that allows the mixedmode on the Sectorscvls -- to check CVget . hsCodeResourceId get . antennasup!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 1414 RbsLocalCell=S1C1 hsCodeResourceId 1 1417 RbsLocalCell=S2C1 hsCodeResourceId 2 1445 RbsLocalCell=S3C1 hsCodeResourceId 3 1415 RbsLocalCell=S4C1 hsCodeResourceId 1 1416 RbsLocalCell=S4C2 hsCodeResourceId 1 1418 RbsLocalCell=S5C1 hsCodeResourceId 2 1419 RbsLocalCell=S5C2 hsCodeResourceId 2 1446 RbsLocalCell=S6C1 hsCodeResourceId 3 1447 RbsLocalCell=S6C2 hsCodeResourceId 3wwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwSCENE 1 : DUW1 primary: numHsCodeResourceId = 3 C1 = U900 VFS1C1: hscoderesourceId = 1S2C1: hscoderesourceId = 1S3C1: hscoderesourceId = 2 C2 =U900 ORS1C2: hscoderesourceId = 3S2C2: hscoderesourceId = 3S3C2: hscoderesourceId = 3 DUW2 secondary: numHsCodeResourceId = 3 C1 = U2100 VFS4C1: hscoderesourceId = 1S5C1: hscoderesourceId = 1S6C1: hscoderesourceId = 2 C2 = U2100 ORS4C2: hscoderesourceId = 3S5C2: hscoderesourceId = 3S6C2: hscoderesourceId = 3!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!SCENE 2 :DUW1 primary: numHsCodeResourceId = 3 C1 = U2100 VF1S1C1: hscoderesourceId = 1S2C1: hscoderesourceId = 2S3C1: hscoderesourceId = 3 C2 =U2100 VFE2S1C2: hscoderesourceId = 1S2C2: hscoderesourceId = 2S3C2: hscoderesourceId = 3DUW2 secondary: numHsCodeResourceId = 3 C3 = U2100 ORS1C3: hscoderesourceId = 3S2C3: hscoderesourceId = 3S3C3: hscoderesourceId = 3DUW U900: numHsCodeResourceId = 3 C1 = U900 VFS1C1: hscoderesourceId = 1S2C1: hscoderesourceId = 1S3C1: hscoderesourceId = 2 C2 =U900 ORS1C2: hscoderesourceId = 3S2C2: hscoderesourceId = 3S3C2: hscoderesourceId = 3------------------------DUW1 primary: numHsCodeResourceId = 3 C1 = U2100 VFS1C1: hscoderesourceId = 1S2C1: hscoderesourceId = 2S3C1: hscoderesourceId = 3 C2 =U2100 VFS1C2: hscoderesourceId = 1S2C2: hscoderesourceId = 2S3C2: hscoderesourceId = 3DUW2 secondary: numHsCodeResourceId = 3 C1 = U2100 ORAS1C3: hscoderesourceId = 3S1C3: hscoderesourceId = 3S1C3: hscoderesourceId = 3!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!SCENE 3 :DUW1 primary: numHsCodeResourceId = 3 C1 = U900 VFS1C1: hscoderesourceId = 1S2C1: hscoderesourceId = 1S3C1: hscoderesourceId = 2 C2 =U900 ORS1C2: hscoderesourceId = 3S2C2: hscoderesourceId = 3S3C2: hscoderesourceId = 3DUW2 secondary: numHsCodeResourceId = 3 C1 = U2100 VFS4C1: hscoderesourceId = 1S5C1: hscoderesourceId = 1S6C1: hscoderesourceId = 2 C2 = U2100 ORS4C2: hscoderesourceId = 3S5C2: hscoderesourceId = 3S6C2: hscoderesourceId = 3 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!SCENE 4 :DUAL DUW 1: numHsCodeResourceId = 3/2 C1 = U2100 VFS1C1: hscoderesourceId = 1S2C1: hscoderesourceId = 2S3C1: hscoderesourceId = 3 C2 = U2100 VFS1C2: hscoderesourceId = 1S2C2: hscoderesourceId = 2S3C2: hscoderesourceId = 3 C3 = U2100 ORS1C3: hscoderesourceId = 1S2C3: hscoderesourceId = 1S3C3: hscoderesourceId = 1 C4 = U2100 ORS1C4: hscoderesourceId = 2S2C4: hscoderesourceId = 2S3C4: hscoderesourceId = 2DUAL DUW 2: numHsCodeResourceId = 2/1 C1 = U900 VFS1C1: hscoderesourceId = 1S2C1: hscoderesourceId = 1S3C1: hscoderesourceId = 2 C2 =U900 ORS1C2: hscoderesourceId = 3S2C2: hscoderesourceId = 3S3C2: hscoderesourceId = 3 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! For GSM 800:Numeral 128 - 251For GSM 900, P-band:Numeral 1 - 124For GSM 900, G1-band:Numeral 0, 975 - 1023For GSM 1800:Numeral 512 - 885For GSM 1900:Numeral 512 - 810 @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@when you look that the import stops at 25% check if the file has that line on the new U900 sectors that you'll be create on the RNCCello Failurecom.ericsson.nms.umts.ranos.cms.nead.segmentserver.csaccess.ProcessingFailureException::The minor operation 'CREATE MO' failed, the defined tags are: [NEIPADR ==> '10.65.111.61' , REASON ==> 'The reason has not been set' , ATTRIBUTENAME ==>sometimes you have to delete the following line on that file:SubNetwork=ONRM_ROOT_MO_R,SubNetwork=RNC662,MeContext=RNC662,ManagedElement=1,RncFunction=1,vsDataMocnCellProfile=1@@@@@@@@@@@@@@@@@@@@@