2013. 01.

ⓒ ⓒ 2013 Zalman Tech Co., Ltd. 2013 Zalman Tech Co., Ltd.

CNPS90F

2013. 01.

CNPS90FUltra Quiet CPU Cooler

Sales Guide


CNPS90F

Honeycomb fin designOptimized heat dissipation structureMinimized noise 92mm FSB fanShark fin blade fanCompact light sizeEasy installation


CNPS90F

Optimized the angle with honeycomb fin, helps to increase the airflow , minimize the noise.

Honeycomb fin design


CNPS90F

FHS(Flower Heat Sink) type heat transfer.Simplified and more direct link to the surface for broader heat dissipation area and more efficient cooling.

일반 히트싱크의 열전달경로Heat source(A)

Heat source (B)

Down blowing type designThrough emitting the air straight from the fan to the mother board, it cools down not only the CPU but also the components around it.

Optimized heat dissipation structure


CNPS90F

One of the Advanced Sleeve bearing FSB Fluid Shield Bearing) applied to prevent dust and strong cooling performance with 92mm fan with minimized noise.

Minimized noise 92mm FSB fan


CNPS90F

Shark fin blade helps to reduce the turbulence generated while the turning of the fan, which helps to reduce noise and vibration, at the same time increases the air flow.

Shark Fin Blade Fan appliedNormal Fan

Shark Fin Blade Fan


CNPS90F

60mm high, small enough to mount into LP(Low Profile) case, perfect for home theater PC, with weight only 240g.

작고 가벼운 사이즈


CNPS90F

Supported socketsIntel Socket LGA 1155/1156/775,AMD Socket FM2/FM1/AM3/AM2+/AM2

멀티 클립 써포터

Easy installationWide compatibility and easy installation.


CNPS90F

SpecificationsDimension 116(L) x 112(W) x 60(H)mm

Weight 240g

Material Pure Aluminum

Fan Size 92mm

Bearing Type

FSB (Fluid Sheild Bearing)

Fan RPM 2300rpm ±10%

Fan Noise 29dBA


CNPS90F

Contents

CNPS80F

Clip Support

Push Pins

Thermal GreaseZM-TG2Manual


CNPS90F

What cases are compatible?

Can be installed in LP(Low Profile) type cases.

※ Dimension: 116(L) x 112(W) x 60(H)mm

※ For cases with air guide make sure there is no interference with the cooler before installing.

Q&A

Is it better to remove the previously applied thermal grease and replace with fresh thermal grease when re-installing the cooler? Yes. The heat transfer performance of thermal compounds may degrade over time. Please wipe off the previously used thermal compound and apply a fresh layer.

What are some cautionary considerations prior to installing the cooler?

For cases with air guide, make sure there is no interference with the cooler before installing. While installing, wear gloves to prevent any possible injury. Also Keep out of the reach for children (do not ingest the thermal grease), and if there is problem with the product, please notify the retailer.

What CPUs are supported?

All single, dual and quad core CPUs based on Intel socket LGA1155/1156/775 and AMD socket FM2/FM1/AM3/AM2+/AM2 are supported.


CNPS90F

What is the max Wattage it supports?

It supports up to 95watts.

What is the thermal resistance value?

The thermal resistance value is 0.3897°C/W. This value can be changed according to the testing environment.

Q&A

The CPU cooler’s base is smaller than the CPU. Will this affect the performance? The metal cover you see outside is actually a heat spreader, and CPU core itself is located under the heat spreader and it is much smaller in size. So, as long as the cooler is mostly in contact with the heat spreader, there is no negative effect on the cooling performance.


CNPS90F

Q&AHow much thermal grease do I need to apply?

It depends on the evenness of the CPU surface. CPUs with uneven surface will require more thermal grease to fill the air pockets created between the CPU and the cooler base. CPUs with even surface will require minimal amount. Generally, it is recommended to apply pea sized amount at the center of the CPU. Mounting the cooler on top of the CPU will evenly distribute the thermal grease.

What is an effective method for wiping off thermal compound from the top(IHS) of the CPU?A dry cloth with a bit of alcohol or acetone is effective. Avoid exposing these chemicals to motherboard and system components.

Wouldn’t the motherboard warp due to the weight of the cooler? If the motherboard warps, would that cause any problems?If the cooler is properly installed as indicated in the User’s Manual, any warping of the motherboard caused by the tension of the cooler’s clip will be within a safe range for stable operation.

Where can I find motherboard compatibility information?

Please visit Zalman website or contact the appropriate customer representative.


CNPS90F

Thank You

2013. 01.

Documents

Transcript of 2013. 01.