ひずみ (strain)ctStrain, Strain Rate, Stress, Modulus, Viscosity, Maxwell model, Relaxation time...
Transcript of ひずみ (strain)ctStrain, Strain Rate, Stress, Modulus, Viscosity, Maxwell model, Relaxation time...
Strain, Strain Rate, Stress,Modulus, Viscosity,
Maxwell model,Relaxation time
Quick Introduction to Rheology
ひずみ (strain)
ずり変形 (shear deformation)
h
x
高さ hを一定にして変形する。体積も変化しない。
ずりひずみ γ =xh
h
ひずみには単位は無い(無次元量)
shear strain
height h = constant. Volume = constant
Strain is a dimensionless quantity
なぜ x/hを使うと便利なのか形・大きさの異なる試料でも、x/hが同じなら同じ変形
h2x2
h1
x1
x1h1
=x2h2
h1
x1
Same deformation
if
ひずみ速度strain rate
ひずみ速度 = ひずみの時間微分
単位は [1/s]
ずり速度 shear rate
γ ≡
dγdt
ずり速度
x上面の移動距離 x
上面の移動速度 vw ≡ x ≡
dxdt
γ =xh
γ =vwh
h
shear rate
とも表せる
単位は [1/s]unit
displacement of the upper surface
velocity of the upper surface
another expressionfor the strain rate
例 example高さ 1cm の試料の上面を、下面に平行に 1mm/s で移動する。
vw = 1 [mm/s]
h = 1 [cm] γ =
vwh
=1 [mm/s]1 [cm]
=1 [mm/s]10 [mm]
∴ γ = 0.1 [1 / s]
h
一定のひずみ速度で変形を続けるとt = 5 秒後のひずみは
γ = γ t = 0.1 [1/s]( ) × 5 [s]( ) = 0.5
x = vwt = 5 [mm]
strain after 5 seconds
ひずみ速度=速度勾配strain rate = velocity gradient
h
0
y
x
vx (y)
試料内部の流れvw vx (y) = ay
vw = vx (h) = aha = vw
h= !γ
高さ yでの流速は yに比例:
上面での流速は
(aは比例係数)
∴vx (y) = !γ y
γ =
∂vx∂y
ひずみ速度 = 速度勾配
下面は固定
flow inside the sample velocity at height y ∝ y
velocity vw at the upper surface y = h
∂vx (y)∂y
= !γ
strain rate = velocity gradient
応力stress
ずり応力 shear stress
力 F面積 S
ずり応力 σ =FSshear stress
応力の単位 unit of stress: パスカル [Pa] = [N/m2]
応力 = 単位面積あたりに働く力
area force
stress = force per unit area
縦に2個積む
面を通して働く力
応力 σ =FS
面積 S力 F
横に2個並べる
σ =FS
F
F
F
σ =2F2S
=FS
力:合計 2F面積:合計 2S
2FS
理想弾性体と理想粘性体
Hookean Solid (ideal solid)and
Newtonian Fluid (ideal fluid)
理想弾性体(フック弾性体)Ideal solid (Hookean solid)
σ (t) = Gγ (t)
理想弾性体では、ひずみが時間変化していても、時刻 tでの応力 σ(t) は同じ時刻におけるひずみ γ(t) だけに比例し、ひずみ速度や過去のひずみには依存しない。
G: ずり弾性率
弾性率 Gの単位は応力と同じで [Pa]
shear modulus
In the ideal solid, stress σ(t) at time t is proportional to the strain γ(t) at the same time t, and does not depend on the strain rate or the past strain.
unit of modulus = unit of stress = [Pa]
理想粘性体(ニュートン流体)Ideal fluid (Newtonian fluid)
ニュートン流体では、ひずみ速度が時間変化していても、或る時刻 tでの応力 σ(t) は同じ時刻でのひずみ速度だけに比例し、ひずみや過去のひずみ速度には依存しない。
σ (t) = η γ (t)
γ (t)
η: ずり粘度shear viscosity
In the ideal fluid, stress σ(t) at time t is proportional to the strain rate at the same time t, and does not depend on the strain or the past strain rate.
!γ (t)
粘度(viscosity)の単位は [Pa s]unit of viscosity = [Pa s]
応力緩和stress relaxation
応力緩和 Stress Relaxation
t
γ(t)
0
γ0
t
σ(t)
0
時刻 t=0 に瞬間変形によりひずみ γ0を与え、そのひずみを維持する(一定の変形に保つ)。Apply step strain γ0 at t=0, and keep the strain constant.
観測される応力は時間とともに減少する。Observed stress decays gradually with time.
γ0 が十分小さければ、入力 γ0 を2倍にすると、出力 σ(t) も2倍。When γ0 is sufficiently small,if γ0 à 2γ0 then σ(t) à 2σ(t) at all t.
2γ0
緩和弾性率 Relaxation Mudulusγ0 が十分小さければ、入力 γ0 を2倍にすると、出力 σ(t) も2倍になる。
G(t) ≡ σ (t)γ 0
緩和弾性率relaxation modulus
When γ0 is sufficiently small,if γ0 à 2γ0 then σ(t) à 2σ(t) at all t.
σ (t)γ 0
はγ0 に依存しない時間の関数になる。a function of time independent of γ0
Maxwell モデル
Maxwell Model
Ideal solid and liquid
σ1(t) = Gγ 1(t)G γ 1
σ1
σ1
“��” “spring”
�� ideal solid
σ 2 (t) = η γ 2 (t)η γ 2
σ 2
σ 2
“�������” “dashpot”
��� ideal liquid
Maxwellモデル
σ1(t) = Gγ 1(t)
σ 2 (t) = η γ 2 (t)
G
η
γ 1
γ 2
σ 2
σ1
σ1
σ 2
“��”
“�������”
��
���
σ (t) = σ1(t) = σ 2 (t)
γ (t) = γ 1(t) + γ 2 (t)
G
η
γ 1
γ 2
γ
σ
σ
Maxwell Model
σ1(t) = Gγ 1(t)
σ 2 (t) = η γ 2 (t)
γ (t) = γ 1(t) + γ 2 (t)
γ 1(t) =1Gσ1(t) =
1Gσ (t)
γ 2 (t) =
1ησ 2 (t) =
1ησ (t)
γ (t) = γ 1(t) + γ 2 (t)
=1Gσ (t) + 1
ησ (t)
γ 1(t) =
1Gσ (t)
dσ (t)dt
+1τσ (t) = G dγ (t)
dtτ ≡
ηG����
�� G ���������������Multiply both sides by G, and exchange left/right-hand sides:
relaxation time
応力緩和 stress relaxation
バネだけが変形 only the spring is deformedγ 1(t = +0) = γ 0
“瞬間”変形の間にはダッシュポットは変形できないdashpot can not deform during the “step strain”
t
γ(t)
0
γ0
“瞬間”変形直後の応力 stress just after the step strainσ (t = +0) =σ 1(t = +0) = Gγ 1(t = +0) = Gγ 0
t > 0: γ (t) = γ 0 = constant
dσ (t)dt
+1τσ (t) = 0 dσ (t)
dt= −
1τσ (t)
G(t) = σ (t)γ 0
= Ge− t /τ
t=+0: “瞬間変形” 直後 just after the “step strain”
dγ (t)dt
= 0
σ (t = +0) = Gγ 0
σ (t)∝ e− t /τ
(a)
(b)
(a) and (b) σ (t) = Gγ 0e− t /τ
G(t)
t0
G
Maxwell モデルの緩和弾性率
G(t) = Ge− t /τ
τ = ηG
τG/e
Relaxation Modulus of Maxwell Model
relaxation time
η = Gτor
[Pa s] = [Pa] [s]
If we know G and τ,we can estimate η
“fluid” at long time
“solid” at short time
G, η and τ
η ~Gτ
For many viscoelastic fluid (such as polymeric liquids)
G = elastic modulus at short time (fast deformation)
η = viscosity at long time (slow deformation)
τ = relaxation time
~ : “roughly” equal