جامعة النجاح الوطنية
-
Upload
augusta-dante -
Category
Documents
-
view
56 -
download
2
description
Transcript of جامعة النجاح الوطنية
جامعة النجاح الوطنية كلية الهندسة
قسم هندسة البناء
عرض ومناقشة مشروع تخرجلنيل درجة البكالوريوس في هندسة البناء
Design of a Commercial Building in Nablus
إشراف الدكتور منذر دويكات
إعداد وتقديم ضياء فواز علي جدو
معاذ ماهر مدني
Outline :Outline :
مخطط الموقع العام
تعريف عام بالمشروع مجمع ال نمر التجاري.تابع لوزارة االوقاف و الشؤون الدينية طوابق.8يتكون المجمع من متر مربع.400باإلضافه إلى طابقين تسويه على مسطح يحتوي على محالت تجارية في الطابق االرضي واالول. .مطعم في الطابق الثاني. كذلك يشتمل هذا المجمع على مكاتب .عيادات متعددة االغراض
التعديالت المعمارية.تم تغيير مدخل المبنى من الجهة الشمالية إلى الجهة الجنوبية
الواجهة الجنوبية
الواجهة الشمالية
التصميم البيئياستخدم المدخة الشمسية في الواجهة الشرقية
التصميم البيئي المعمارينسبت بلغت حيث عليه هو عما الشمالية الواجهة في الزجاجية المساحات من التقليل
الزجاجية إلى% 45المساحات الشمالية، للوجهة الكلية المساحة من %. 20من يقلل وهذاشتاءا المبنى لتدفئة الالزمة الطاقه
متطلبات السالمة العامةتوفير مخرج الطوارئ باإلضافة إلى المدخل الرئيسي
.للمبنى
متطلبات السامة العامة.تزويد المبنى بإشارات لمخرج الطوارئ
تزويد أنظمة اإلنارة مخرج الطوارئ ببطاريات تعمل عند .حدوث انقطاع التيار الكهربائي تلقائيا
نظام إطفاء الحريق
Structural Design
Materials
Structural materials
Concrete:
Concrete strength for all concrete parts is B300 ( f’c = 250 Kg\cm2)
Modulus of elasticity equals (2.5*105 Kg\cm2) Unit weight is (2500 kg\m3)
Steel:
Modulus of elasticity equals( 2*106 Kg\cm2) For steel reinforcement, is( 4200 Kg\cm2)
Non-structural materials
They are mainly, blocks, plasters, tiles, filling, mortar and masonry.
Codes and Standards
The following codes and standards are used in this study:
ACI 318-08 : American Concrete Institute provisions for reinforced concrete structural design.
UBC-97 : Uniform Building Code provisions for seismic load parameters determination.
IBC-2009 : International Building Code, which is used here for live loads.
Loads and Load combinations
Loads
1) Gravity loads:
Live load:For Basement – second Floor = 0.5 t/m2
For Third – Eighth Floor = 0.3 t/m2
Dead load:
. The super imposed dead load = 0.4 t/m2.
2) Lateral loads:
Seismic loads:
The UBC97 code seismic parameters are as follows:
The seismic zone factor, Z= 0.2 . The importance factor, I = 1.0 . The ductility factor, R = 5.5 . The seismic coefficient, Ca = 0.18 .
The seismic coefficient, Cv = 0.25 .
Load combinations:
The ACI318-08 load combinations are used and they are summarized as follows:
U1 = 1.4D U2 = 1.2D + 1.6L + 1.6HU3 = 1.2D + 1.0E + 1.0LU4 = 0.9D + 1.0E + 1.6H Where: D : is dead load L : is live load H : is weight and pressure load of soil E : is earthquake load
hmin = l/21 = 640/21 = 30.5 cm Use h=30 cm
Ribbed slab analysis and design :The thickness of the slab:
Dimension of Beam: Beams
Dimension
B1 ( 60 * 30)
B2 ( 80 * 30)
B3 ( 100 * 30)
B4 ( 100 * 30)
B5 ( 100 * 30)
B6 ( 100 * 30)
B7 ( 100 * 30)
B8 ( 100 * 30)
B9 ( 50 * 30)
B10 ( 80 * 30)
B11 ( 80 * 30)
B12 ( 80 * 30)
B13 ( 80 * 30)
Dimension of columns:
Columns Dimension
C1 ( 30 * 60)
C2 ( 60 * 60)
C3 ( 60 * 60)
C4 ( 60 * 60)
C5 ( 50 * 50)
C6 ( 100 * 30)
C7 ( 30 * 80)
C8 ( 30 * 140)
C9 ( 30 * 120)
Structural Analysis and Design
3D model . Dynamic analysis . Soil springs structure interaction.
Property/Stiffness Modification Factors
Basic calculations
Check Compatibility
Structural Model Verification : Check Equilibrium
Error % < 5% ok.
Load SAP Manual Error%
D.L 7955 t 7841 t 1.4%
L.L 1878 t 1871 t 0.3%
Check the moments on the beams :
Beams SAP Manual Error%
B4 32.6 t.m 27.9 t.m 14.4
B2 4.4 t.m 4.5 t.m 2.2
B9 2.5 t.m 0.9 t.m 64
Check the loads on columns:Columns SAP Manual Error%
C1 170 t 78 t 54
C4 467 t 481 t 3
C9 157 t 239 t 52
Design of slabsDesign of slabs :
*Analysis and Design of Beams:
Design of columns
Analysis and Design of Footings Total Area of plan 400 meter square . Total load of building about 10000 ton. Allowable bearing capacity 1.5 Kg\cm2. After improving the soil under footing using base coarse the
allowable bearing capacity become 2.1 Kg\cm. To carry this load with less deferential settlement we use mat
foundation.
50 c
m50
cm
نوعية توضح صورة التربة
Design of Footings
Design of FootingsReinforcement in long direction.
Design of FootingsReinforcement in short direction.
Design of FootingsSection in mat foundation:
Mechanical Design.Main pipe from Municipality
Mechanical Design.Drainage system and potable water for basement.
Mechanical Design.
Drainage system and potable water for bath room men & women.
Mechanical Design.
Drainage system and potable water for 3-8 floor (office floor).
Sample calculation for office 1 : For calculate number of lamps in offices use the
follow laws : ,
Ku= 23.5\ 2.75(5.5+4.26) = 0.87
3. =N= (23.5 * 300 )\ 2 * 0.47 * 0.9 * 2800
Electrical Design
Distribution lamps
Distribution socket's
Panel (DB ) :