Post on 04-Jun-2018
8/13/2019 placi curbe - 9
1/14
8/13/2019 placi curbe - 9
2/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX A n Membrane theor stresses in shells
A1 General Action effects and resistances: characteristic values of the action
effect or resistance are provided when characteristic values of the
actions, geometric parameters and material properties are adopted. .
Boundary conditions:
the boundary conditions for cylinders: radially free at both ends, axiallysupported at one end, and rotationally restrained at both ends.
shell wall, so that the combined stress resultant introduced into the shellis solely in the direction of the shell meridian.
,at one end, and rotationally restrained at both ends.
Sign convention: The sign convention for stresses should be takeneveryw ere as ens on pos ve.
8/13/2019 placi curbe - 9
3/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX A Membrane theor stresses in shells
A2 Unstiffened Cylindrical ShellsThe followin fi ures ive the values of internal forces and stresses
for different loading situations
8/13/2019 placi curbe - 9
4/14
8/13/2019 placi curbe - 9
5/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX A Membrane theor stresses in shells
A3 Unstiffened Conical Shells
8/13/2019 placi curbe - 9
6/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX B n Additional ex ressions for lastic
B1 General Resistances: The resistances calculated usin the ex ressions in
collapse resistances
this annex may be assumed to provide characteristic values of the
resistance when characteristic values of the geometric parameters. Notations: specific for geometrical dimensions, stresses and loads,
according to 1.4.
the boundary condition notations should be taken as detailed in 5.2.2.
the term clamped should be taken to refer to BC1r and the termpinned to refer to BC2f.
8/13/2019 placi curbe - 9
7/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX B Ex ressions for lastic resistances
B2 Unstiffened Cylindrical Shells
nR unit circumference) is given by:
Range of applicability:Dependent parameters:
The lastic resistance P force erunit circumference) is given by:
8/13/2019 placi curbe - 9
8/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX B Ex ressions for lastic resistances
B2 Unstiffened Cylindrical Shells
Range of applicability:
The plastic resistance ( P n and p nalwa s ositive outwards aregiven by:
8/13/2019 placi curbe - 9
9/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX B Ex ressions for lastic resistances
B3 Ring Stiffened Cylindrical Shells The plasticresistance P nR (forceper unitcircumference) isgiven by:
Range of applicability:
The plastic resistance P nR (force perun c rcum erence s g ven y:
8/13/2019 placi curbe - 9
10/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX B Ex ressions for lastic resistances
B3 Ring Stiffened Cylindrical Shells
Range of applicability:
n nalways positive outwards) aregiven by:
8/13/2019 placi curbe - 9
11/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX B Ex ressions for lastic resistances
B4 Junctions between shellsDependent parameters:
The plastic resistance is given by:
Range of applicability:
8/13/2019 placi curbe - 9
12/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX B Ex ressions for lastic resistances
B4 Junctions between shells
Dependent parameters:
The plastic resistance is given by:
8/13/2019 placi curbe - 9
13/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX B Ex ressions for lastic resistances
B5 Circular plates with axisymmetric boundary conditions
8/13/2019 placi curbe - 9
14/14
EN 1993-1-6 DESIGN CHECKING OF SHELLSANNEX B Ex ressions for lastic resistances
B5 Circular plates with axisymmetric boundary conditions