Post on 08-Nov-2021
MANUALE D’USO/USER’S MANUAL
GUIDE
sc 1
5-1
1-2
011
COMPOSIZIONE GUIDE: REGOLE BASE
0 punti chiave
1. PARTIRE SEMPRE DALLE MISURE DEL TAGLIO FINITO
2. DETERMINARE LA TIPOLOGIA ELA QUANTITA’ DI PROFILI E TESTATE.
3. SCEGLIERE TIPOLOGIA DI APPARECCHI:
4. DETERMINARE ACCESSORI IN BASE ALLA TIPOLOGIA DI APPARECCHI:
- FLUORESCENTI- SPOT- FLUORESCENTI + SPOT
- FLUORESCENTI- SPOT- FLUORESCENTI + SPOT
OGNI TESTATA DEFINISCE UNA
PORZIONE DI TAGLIO FINITO DI
LUNGHEZZA UNA COPPIA250 MM.
500MM
GLI ELEMENTI ANGOLARI DI
PROFILO DEFINISCONO UNA
PORZIONE DI TAGLIO FINITO DI
LUNGHEZZA: (TAGLIO 138) E
(TAGLIO 68MM)
250MM
180 MM
SOLO FLUORESCENTE: pag.8
SOLO SPOT: pag.5
FLUORESCENTE + SPOT: pag.9,16,19
Nella composizione dei canali considerarerispetto
alla lunghezza di taglio che si vuole ottenerenel cartongesso.
100mm in più per ciascuna estremità
CANALE DI COPERTURA
(IN ALTERNATIVA CARTONGESSO A CURA DELL’ISTALLATORE)
TESTATE DI CHIUSURA
FARETTI SPOT E ALIMENTATORI
PAG.6
PROFILO INCLINATO DI FINITURA
(OPZIONALE)
CANALE DI COPERTURA
(IN CORRISPONDENZA DEI SOLI FARETTI E DELLE REGLETTE INDIRETTE)
TESTATE DI CHIUSURA
PROFILO INCLINATO DI FINITURA(IN CORRISPONDENZA DEI SOLI FARETTI E DELLE REGLETTE INDIRETTE - OPZIONALE)
REGLETTE FLUORESCENTI + DIFFUSORI
PARATIE INTERMEDIE
(TRA FLUORESCENTI E FARETTI)
FARETTI SPOT E ALIMENTATORI
Nella composizione dei canali terminali, qualorapresenti, considerare rispetto allalunghezza della porzione di taglio individuatadai canali.
100mm
500
mm
250
mm
180
mm
1
Nell’ effettuare il taglio nel cartongesso si deveprevedere un taglio finitorispetto alla misura della lampada da installare.Nel caso di più apparecchi fluorescenti in linea,
inferiore di 20mm
togliere 20mm una sola volta.
REGLETTE FLUORESCENTI DIRETTE O INDIRETTE
DIFFUSORI DIRETTI O INDIRETTI
PARATIA INTERMEDIA(UNA PER TUTTA LA COMPOSIZIONE)
GUIDE SYSTEM: BASIC RULES
0 bullet points
1. START FROM THE DIMENSIONS OF THE FINISHED CUT YOU WANT TO OBTAIN
2. DETERMINE QUANTITY AN TYPE OFLINEAR PROFILE AND HEAD FRAME.
3. CHOOSE TYPE OF LIGHTING FIXTURES:
4. DETERMINE ACCESSORIES BY TYPE OF EQUIPMENT:
- FLUORESCENT- SPOTLIGHT- FLUORESCENT + SPOTLIGHT
- FLUORESCENT- SPOTLIGHT- FLUORESCENT + SPOTLIGHT
EACH HEAD FRAME DEFINES A PORTION
OF CUT A COUPLE OF HEAD
FRAME A PORTION OF CUT
L=250MM,
L=500MM
ANGULAR ELEMENTS DEFINE A
PORTION OF CUT (138MM
CUT) OR (68MM CUT)
L=250MM
L=180MM
FLUORESCENT ONLY: pag.8
SPOTLIGHT ONLY: pag.5
Making the composition of the metal boxcover thanthe lenght of the cut you need on theplasterboard.
consider +100mm for both ends
BOX COVER
(OR PLASTERBOARD - NOT PROVIDED, TO BE DONE ON SITE )
METAL HEAD FOR BOX COVER
SPOTLIGHT AND TRASFORMER/BALLAST
PAG.6
INCLINED PAINTED PROFILE
(OPTIONAL)
BOX COVER
(IN CORRISPONDENCEOF SPOTLIGHTS AND INDIRECT BATTENS ONLY)
500
mm
250
mm
180
mm
2
FLUORESCENT + SPOTLIGHT: PAG.9,16,19
FLUORESCENT DIRECT OR INDIRECTBATTENS
DIRECT OR INDIRECT DIFFUSERMaking the cut in the plasterboard, considerthat the finished cut thanthe size of the lamp to be installed.
must be 20mm lower
In case of multiple fluorescent fixtures in line,remove once 20mm.
METAL PART FOR DIRECT FLUO(ONE FOR THE WHOLE COMPOSITION)
INCLINED PAINTED PROFILE(IN CORRISPONDENCE OF SPOTLIGHTS AND INDIRECT BATTENS ONLY - OPTIONAL)
METAL HEAD FOR BOX COVER
METAL PART FOR DIRECT FLUO(BETWEEN SPOTLIGHT AND BATTENS)
SPOTLIGHT AND TRASFORMER/BALLAST
FLUORESCENT DIRECT OR INDIRECT + DIFFUSERBATTENS
Making the composition of the metal boxcover thanthe lenght of the cut you need on theplasterboard.
consider +100mm for both ends
DIFFUSORELUCE INDIRETTA
GANCIO PER RENDEREPORTANTE LA STRUTTURA
GUIDE PER VITI M4
100 mm
45 mm
30 mm
60 mm
15 mm
BATTUTA PER CARTONGESSO
CANALE PER VITE AUTOFILETTANTE
DIFFUSORELUCE DIRETTA
Sistema Guide - Guide system:
Sistema modulare per cartongesso daincasso a scomparsa totale con il quale èpossibile realizzare tagli nel cartongesso diforma rettilinea, rettangolare e ad L.Installabile su pareti orizzontali e verticali.
Recessed modular system for plasterboardfor straight, rectangular and “L” cuts.To fix to plaster and smooth horizontal orvertical wall.
Vite autoforanteper cartongessoSelf drilling screwfor plasterboard
Rete in fibra di vetro/glass fiber mesh
15 mm
TAGLIO 68mm
TAGLIO 138mm
138 mm
198 mm
68 mm
128 mm
Montaggio su cartongesso
Taglio di luce da 68mm
lunghezza desiderata +36mm e di larghezza di128mm.
Taglio di luce da 138mm
lunghezza desiderata+36mm e di larghezza di198mm.
:-Bloccare il profilo al cartongesso con delle vitiautoforanti ad una distanza di 60mm dal bordo.
-Inserire una rete in fibra di vetro.
-Stuccare e rasare.
Nota: per un cartongesso di altezza inferiore a 15mminserire una piastra di spessore adeguato.
-Effettuare un taglio rettangolare sul cartongessodella
-Effettuare un taglio rettangolare sul cartongessodella
Fitting on the plastboard
68mm cut
of the
lenght you prefer adding +36mm and 128mm wide.
138mm cut
of the
lenght you prefer adding +36mm and 198mm wide.
:
-Fix the profile on the plastboard with a selfdrillingscrews at 60mm from the cut.
-Insert a fiber glass net.
-Plaster and leveling.
Please Note: for a plasterboard smaller than 15mminclude a right thiknetplace
-make a rettangular cut on the plasterboard
-make a rettangular cut on the plasterboard
3
- Proiettori con sistema di aggancio a vite sul telaio,facilmente installabili e posizionabili nella posizione chesi preferisce.- Non sono compresi alimentatori o trasformatori.
Proiettori
LT 2050 1XMAX100W 12 V G53 Qr111 LT 2051 1X50W 12 V GU5.3 QRCBC51
LT 2052 1XMAX 70W GX8,5 CDMR111
LT 2054RLT 2055R
1XMAX 70W G12 40° HQI1XMAX 70WE27 HQI PAR30
LT 2060 Anello di finitura per lampada Qr111 e CDMR111Finishing ring for Qr111 and CDMR111
LT 2054CLT 2055C
1XMAX 70W G12 40° HQI1XMAX 70WE27 HQI PAR30
Spotlights
- Spotlights available with direct hanging wayover the frame.
- Adjustable lights and easy to install.
- Ballasts or transformers are not included.
Installazione proiettori
- Installare i proiettori prima dei canali di copertura.- Inserire il piastrino di aggancio all’interno dei canalidel profilo guide.- Bloccare il piastrino di aggancio con la vite indotazione.- Cablare il proiettore utilizzando alimentatori otrasformatori ( a seconda del modello) idoneiall’installazione remota su cartongesso.- Piegare verso il basso il proiettore.- Inserire il canale al di sopra del faretto.
Installation of the spotlights
- Install the spotlight before the cover. .- Insert the hanger inside the channels of the profile- Block the hanger with the screws included.- Wire the spotlight using ballasts or transformers rightto be fit away from the plasterboard.- Bend down the spotlight.- Insert the metal box cover over the spotlight.
4
Guide canale rettilinee- Guide straight cover:installable on 138mm or 68mm cut.
LT 2031LT 2032LT 2033LT 2034LT 2035LT 2031.68LT 2032.68LT 2033.68LT 2034.68LT 2035.68
installabile su taglio da 138mm L. 300mminstallabile su taglio da 138mm L. 500mminstallabile su taglio da 138mm L. 700mminstallabile su taglio da 138mm L. 1000mminstallabile su taglio da 138mm L. 1200mm
installabile su taglio da 68mm L. 300mminstallabile su taglio da 68mm L. 500mminstallabile su taglio da 68mm L. 700mminstallabile su taglio da 68mm L. 1000mminstallabile su taglio da 68mm L. 1200mm
Guide canale d’angoloCouple of angle closing head box:
LT 2038LT 2038.68
installabile su taglio da 138mminstallabile su taglio da 68mm
H > 200 mm
100 mm
x
Guide coppia testata canaleCouple of closing head box:
LT 2036LT 2036.68
installabile su taglio da 138mminstallabile su taglio da 68mm
Canali testate e paratieGuide metalbox cover and elements to separate
- Moduli di canali da inserire sui telai in alluminio.- Modules of cover to insert on the aluminium frame.
- Sono disponibili nei seguenti colori- available in thiscolour: /01 bianco (white) /02 nero (black)
Note
lunghezza del taglio ottenuto +100 mm per ogni testata
- I moduli vengono consegnati stesi con preforature peressere piegati a mano in cantiere.- Installare i canali solo dopo aver installato e cablatoi faretti.- Altezza minima necessaria per l’installazione 200mmdalla faccia inferiore del cartongesso.- I canali sono dotati di asole verticali per il passaggio deicavi di cablaggio.- Nella composizione dei canali considerare 100mm in piùper entrambe le estremità rispetto alla lunghezza di taglioche si vuole ottenere nel cartongesso.
installazione
-Inserire i canali al di sopra del taglio nel cartongesso.-Appoggiare la lamiera all’interno dell’ultimagola del profilo.-Far passare i cavi di alimentazione attraverso leasole del canale.-Fissare il canale con le viti in dotazione.
155 mm
Notes:
Installation:
- modules are sold perforated to fold it easily directly atyard.- Install the metalbox cover only after the wiring andinstallation of the spotlights.- H. minimum 200mm from the down point of theplastboard.- The metal box cover has vertical eylets to permit the wiretransit.- Making the composition of the metal box cover consider+100mm for both ends than the lenght of the cut youneed on the plasterboard.
- Insert the metal box cover over the cut on theplasterboard.- Support the metalbody inside the last eylets of thechannel.- Transit the wires through the eylets of the channel.- Fix the channel with the included screws
310 mm
5
L
L
60
L
LL
L
taglio 138 taglio 68
L
60
Ø 115
140
Ø 100
150
Ø 115
72
Ø 63
66
Ø 55
105
Ø 111
120
Ø 63
66
Ø 55
105
6
H >120 mm
schermo/screen
Fluo diretto/ fluorescent direct battens
per taglio 138mm / For 138mm cut
138 mm
LT2071
LT2071D
LT2073
LT2073D
LT2075
LT2075D
LT2077
LT2077D
2x14-24W G5 T5 L=2x14-24W G5 T5 touch dimm
2x21-39W G5 T52x21-39W G5 T5 touch dimm
2x28-54W G5 T528-54W G5 T5 touch dimm
2x35-49-80W G5 T52x35-49-80W G5 T5 touch dimm
575
L=875
L=1175
L=1475
per taglio 68mm / For 68mm cut
LT14.68
LT14D.68
LT21.68
LT21D.68
LT28.68
LT28D.68
1x14-24W G5 SEAMLESS1x14-24W G5 SEAMLESS touch dimm
1x21-39W G5 SEAMLESS1x21-39W G5 SEAMLESS touch dimm
1x28-54W G5 SEAMLESS1x28-54W G5 SEAMLESStouch dimm
L=585
L=885
L=1185
LT14.138
LT14D.138
LT21.
LT21D.
LT28.
LT28D.
1x14-24W G5 SEAMLESS1x14-24W G5 SEAMLESS touch dimm
1x21-39W G5 SEAMLESS1x21-39W G5 SEAMLESS touch dimm
1x28-54W G5 SEAMLESS1x28-54W G5 SEAMLESStouch dimm
L=585
L=885
L=1185
138
138
138
138
LT2071SL
LT2071DSL
LT2073SL
LT2073DSL
LT2075SL
LT2075DSL
2x14-24W G5 SEAMLESS2x14-24W G5 SEAMLESS touch dimm
2x21-39W G5 SEAMLESS2x21-39W G5 SEAMLESS
2x28-54W G5 SEAMLESS2x28-54W G5 SEAMLESS
L= 585
L=885touch dimm
L=1185touch dimm
SOLO FLUORESCENTE/only fluorescent
Nell’ effettuare il taglio nel cartongesso si deveprevedere un taglio finito rispetto allamisura della lampada da installare.Nel caso di più apparecchi fluorescenti in linea,
inferiore di 20mm
togliere
Making the cut in the plasterboard, consider that thefinished cut must be 20mm lower than the size of thelamp to be installed.
In case of multiple fluorescent fixtures in line, remove
once 20mm.
taglio finito/ :
2330mm
finished cut2x1175mm=23502350mm-20mm=
reglette/ :battens2x28-54W (1175mm)
-20mm
7
LT2112 FUORI PRODUZIONE - DISCONTINUED
LT2190 PARATIA COPPIA - INTERMEDIATE METAL PARTCOUPLE: TO BE USED WITH FLUORESCENT DIRECT BATTENS(1 COUPLE EACH LINE OF FLUORESCENT DIRECT BATTENS)
-Nella composizione di più moduli fluo indiretti, tenerepresente che le reglette si sovrappongono di 80mm/in thecomposition of several modules fluo indirect, hold that theoverlap is 80mm.
-Cablare il corpo utilizzando l’apposita morsettiera primadi installarlo sul cartongesso/At first wire the lamp using theterminal block before to install the lamp on the plasterboard.-Inserire il corpo all’interno del taglio nel cartongesso/Fill-inthe body of the lamp in the cut of the plasterboard.-Assicurare il corpo illuminante al profilo tramite le viti indotazione/Screw the lamp to the profile using.-Inserire delle lampade adeguate come da descrizioneprodotto/Use appropriate bulbs.-Inserire infine lo schermo verticale nella primascanalatura del profilo/Fill finally the vertical screen in the firstgroove profile.
+80mm una volta/
once
1x14W L.500mm1x21W L.800mm1x28W L.1100mm1x35W L.1400mm
L.580mmL.880mmL.1180mmL.1480mm
LT 2101-01/DLT 2103-03/DLT 2105-05/DLT 2107-07/D
diffusore fluo indiretto/ indirect diffuser screen:
LT 2120LT 2121LT 2122LT 2123
Fluo indiretto
- Moduli fluorescenti monolampada T5 attacco G5 a luceindiretta con alimentazione elettronica normale odimmerabile switch-dimm (/D)/Fluorescent single bulb T5indirect lighting module with normal or electronic power.
- Sono installabili sia su taglio da 68mm cha da 138mm /They are installed on both cut from 68mm to 138mm.
- Altezza minima per l’installazione 125mm/Minimumheight 125mm for installation.
+60mm una volta/
once
1x14W L.520mm1x21W L.820mm1x28W L.1 0mm1x35W L.1420mm
L.580mmL.880mmL.1180mmL.1480mm
LT 2101-01/DLT 2103-03/DLT 2105-05/DLT 2107-07/D
diffusore fluo indiretto/ indirect diffuser screen:
LT 2120LT 2121LT 2122LT 2123
12
gennaio 2012
la sovrpposizione 60 mm si può mantenere: non ci sono problemi nelle composizioni già fatte
138mmØ111mm spots
Ø111mm spots
138mmØ50mm spots
Ø50mm spots
fluo indirect
fluo indirect
Fluo indiretto + spot /fluorescent indirect + spotlightsyou can install both fluorescent and spotlights in the following situations:
68mmØ111mm spots
Ø111mm spots
68mmØ50mm spots
Ø50mm spots
fluo indirect
fluo indirect
8
80 m
m
schermo/screen
old version new version
overlap 60mm
H >
10
0 m
m
80 m
m
schermo/screen
use with Luciferos metal box
use with plasterboard
200 m
m
ceiling
plasterboard
use with Luciferos metal box
use with plasterboard
120 m
m
120 m
m
H >
12
5 m
m
155 m
m(m
eta
l bo
x c
ove
r)
200 m
m
155 m
m(m
eta
l bo
x c
ove
r)
ceiling
overlap 80mm
(from november 2011)
9
Esempio di creazione di un taglio di 138x1000 mma soffitto:Example how to make a 138x1000 mm cut in
the ceiling.
- Tagliare il cartongesso a misura:
- Inserire una delle testate della coppia di testate pertaglio da 138mm ( LT 2010 )all’interno del foro praticatonel cartongesso.- Insert one of the head frame included for the 138mm cut(Lt2010) in the hole made on the plasterboard.
- Fissare la testata con delle viti autoforanti tenendofermo il profilo.- Fix the headframe with a selfdrilling screws and take caredon’t move the profile during the operation.
- Inserire i tratti rettilinei all’interno del taglio effettuato.- Insert the straight elements inside the cut.
- Bloccare i tratti rettilinei (LT 2016 )serrando i granidei giunti in dotazione.- Bolck the straight elements screwing the screws of theconnector.
- Fissare il tratto rettilineo con delle viti autoforantitenendo fermo il profilo.- Fix the straight elements with selfdrilling screws inside andtake care don’t move the profile during the operation.
- Inserire la seconda testata.- Insert the secon head frame.
- Bloccare la seconda testata serrando i grani dei giuntiin dotazione.- Bolck the second head frame screwing the screws of theconnector.
- Fissare la testata con delle viti autoforanti tenendofermo il profilo.
- Fix the head frame with selfdrilling screws inside and takecare don’t move the profile during the operation.
cut the plasterboard
174 mm x 1036mm
10
- Inserire le rete in fibra di vetro ( non in dotazione )- insert the fiberglass net ( not included)
- Stuccare e rasare.- Plaster and leveling.
- Pitturare.- Paint.
11
Cablaggio/Wire:
Seguire gli schemi a fianco riportati/Follow the wiring diagrams shown at the side.
D1
D2
ESEMPI/EXAMPLES
12
138
Creazione di una composizione lineare L=1500mm, taglio 138mm con 3 faretti Lt2050 e profilo inclinato di finitura::How to create a linear compostion L=1500mm, 138mm cut with 3 spotlights Lt2050 and inclined plane
1500
250 250
Guide rettilinee (coppie)Straight aluminium guide (couple)
L= 500 mmLT 2016LT 2017LT 2018LT 2019LT 2020
L= 1000 mmL=1500 mmL=2000 mmL=3000 mm
Articoli:
LT 2010 Guide testata telaio L.138mm (coppia)Guide head-frame mm138 wide (couple)
338 mm250 mm
350 mm250
NR:
1
1
LT 2013 Giunti rettilinei (coppia)straight connector (couple)
15
5
15
5
138 mm
Guide canale rettilinee- Guide straight cover:installable on 138mm or 68mm cut.
installabile su taglio da 138mm L. 300mminstallabile su taglio da 138mm L. 500mminstallabile su taglio da 138mm L. 700mminstallabile su taglio da 138mm L. 1000mminstallabile su taglio da 138mm L. 1200mm
LT 2031LT 2032LT 2033LT 2034LT 2035
LT 2036
installabile su taglio da 138mm
Guide coppia testata canaleCouple of closing head box
1
1
0spare
parts only
TRAS/105 TRASFORMATORE 105VA
LT 2050 1XMAX100W 12 V G53 Qr111
3
3
L
L
LT 2010PL Guide profilo inclinatoGuide inclined plane
Guide profilo profilo inclinato (coppia)Inclined plane Guide (couple)
L= 500 mmLT 20PL.500L= 1000 mmL=1500 mmL=2000 mmL=3000 mm
LT 20PL.1000LT 20PL.1500LT 20PL.2000LT 20PL.3000
1
1
13
138
Creazione di una composizione lineare L=1455mm, taglio 138mm completamente fluorescente::How to create a linear compostion L=1455mm full fluorescent
1455
250 250
Guide rettilinee (coppie)Straight aluminium guide (couple)
L= 500 mmLT 2016LT 2017LT 2018LT 2019LT 2020
L= 1000 mmL=1500 mmL=2000 mmL=3000 mm
Articoli:
LT 2010 Guide testata telaio L.138mm (coppia)Guide head-frame mm138 wide (couple)
338 mm250 mm
350 mm250
NR:
1
1
LT 2013 Giunti rettilinei (coppia)straight connector (couple)
138 mm
1
0spare
parts only
L
L
Guide reglette fluorescente diretta:Guide fluorescent batten direct.
LT2071LT2071DLt2073LT2073DLt2075LT2075DLt2077LT2077D
2x14-24W G5 T5 L=5752x14-24W G5 T5 touch dimm
2x21-39W G5 T5 L=8752x21-39W G5 T5 touch dimm
2x28-54W G5 T5 L=117528-54W G5 T5 touch dimm
2x35-49-80W G5 T5 L=14752x35-49-80W G5 T5 touch dimm
LT 2190 Paratia intermedia canale-fluo (coppia)Metal part for direct fluorescent element
L
Guide diffusore diretto:Guide direct diffuser.
LT2080LT2081LT2082LT2083
L=574 taglio 138L=874 taglio 138L=1174 taglio 138L=1474 taglio 138
1
1
to be cut on site
14
Esempio di creazione di un angolo 1500x1000mm fluorescente + spot LT2052::How to create an angular compostion 1500x1000mm fluorescent + spotlight Lt2052
11
0
110
10
00
24
85
00
25
0
1500
2501000250
13
8
Guide rettilinee (coppie)Straight aluminium guide (couple)
X= 500 mmLT 2016LT 2017LT 2018LT 2019LT 2020
X= 1000 mmX=1500 mmX=2000 mmX=3000 mm
Articoli:
LT 2010 Guide testata telaio L.138mm (coppia)Guide head-frame mm138 wide (couple)
338 mm250 mm
350 mm250
NR:
1
1
138 mm
fluorescent batten 28-54W
LT 2012 Guide angolo esternoGuide exterior angle
LT 2011 Guide angolo internoGuide interior angle
250
112
15
5
LT 2036
installabile su taglio da 138mm
Guide coppia testata canaleCouple of closing head box 1
155
LT 2038 Guide box angolo internoGuide box cover for interior corner
L
1
15
15
5
Guide canale rettilinee- Guide straight cover:installable on 138mm or 68mm cut.
installabile su taglio da 138mm L. 300mminstallabile su taglio da 138mm L. 500mminstallabile su taglio da 138mm L. 700mminstallabile su taglio da 138mm L. 1000mminstallabile su taglio da 138mm L. 1200mm
LT 2031LT 2032LT 2033LT 2034LT 2035
1
L
Guide reglette fluorescente diretta:Guide fluorescent batten direct.
LT2071LT2071DLt2073LT2073DLt2075LT2075DLt2077LT2077D
2x14-24W G5 T5 L=5752x14-24W G5 T5 touch dimm
2x21-39W G5 T5 L=8752x21-39W G5 T5 touch dimm
2x28-54W G5 T5 L=117528-54W G5 T5 touch dimm
2x35-49-80W G5 T5 L=14752x35-49-80W G5 T5 touch dimm
LT 2190 Paratia intermedia canale-fluo (coppia)Metal part for direct fluorescent element
L
Guide diffusore diretto:Guide direct diffuser.
LT2080LT2081LT2082LT2083
L=574 taglio 138L=874 taglio 138L=1174 taglio 138L=1474 taglio 138
1
1
1
16
1
AEHQI.35C ELECTRONIC BALLAST HQI 35W
LT 2052 1x35 OR 70W GX8,5 HQI CDM-R111
4
4
AEHQI.70C ELECTRONIC BALLAST HQI 70W
OR