Post on 04-Aug-2018
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
2011 American Honda Motor Co., Inc. All Rights Re
AII 12085
REMOTE CONTROL ENGINE
STARTER
served. AII 46215 (1112
CR-V
) 0
Issue Date
DEC 2011
PARTS LIST
Remote Control Engine Starter Unit KitP/N 08E91-E22-101A
Transmitter
Control unit
Antenna
Key ring
Protective tape
Fuse label
Caution label
Accessory Users Information Manual
Quick Start Guide
Remote Control Engine Starter Attachment KitP/N 08E92-T0A-100A
Control unit bracket
Engine starter harness
3 Relays
8 mm Nut
20 Wire ties
1 of 278E92-T0A-1A00-90
Long wire tie
7 Urethane tapes
Template
Clip
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Diagonal cutters
Ratchet
8 mm, 10 mm, and 12 mm Sockets
Combination wrench
Isopropyl alcohol
Scissors
Small flat-tip screwdriver
Shop towel
Ruler
Tape measure
HDS (Honda Diagnostic System)
Needle nose pliers
Masking tape
Electrical tape
The following tool is available through the Honda Tool and Equipment Program. On the iN click on: Service > Service Bay > Tool and Equipment Program, the enter the number under search. Or call 888-424-6857.
Trim Tool Set (T/N SOJATP2014)
2 of 27 AII 46215
Illustration of the Remote Control Engine Starter Installed on the Vehicle
INSTALLATION
NOTE: This antenna should only be installed if the ambient air temperature 15C (60F) or above.
1. Move the drivers seat all the way back.
2. Disconnect the negative cable from the battery.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers.
Q0N2312AG
40A FUSE
CONTROL UNITANTENNA
3 RELAYS
3A FUSEENGINE STARTER HARNESS
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
Setting the Control Unit
3. Using a small flat-tip screwdriver, set the switches on the (accessory) control unit to the locations shown.
NOTE:
The switches must be set before the control unit is plugged in.
If the switch settings are not correct, the remote engine starter will not operate correctly.
If setting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the new settings are recognized.
921301AD
CONTROL UNITSMALL FLAT-TIP
SCREWDRIVER
Discharge any static electricity.
SET
SWITCHES
SWITCHES
SW:1 RR Junction unit --------------------> OFF
SW:2 Trunk or Tailgate --------------------> ON
SW:3 Smart Entry----------------------------> OFF
SW:4 Horn or Buzzer Answerback-----> OFF
SW:5 Trunk Main SW -----------------------> OFF
SW:6 Reserve ---------------------------------> OFF
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
4. Using isopropyl alcohol on a shop towel, clean the control unit where the protective tape will attach. Remove the adhesive backing, and attach the protective tape to the control unit over the switches.
Removing the Vehicle Parts
5. Remove the roof console.
Using a plastic trim tool, pry out and remove the left and right lens (four retaining tabs each).
Open the sunglass holder and remove the four screws.
Remove the roof console (unplug the vehicle connectors).
772505AS
CONTROL UNIT
SWITCHESPROTECTIVE TAPE
ADHESIVE BACKINGRemove.
Clean with isopropyl alcohol.
Q0N2012AG
VEHICLE CONNECTORS
ROOF CONSOLE
4 SCREWS
4 RETAINING TABS
LEFT LENS
SUNGLASS HOLDEROpen.
4 RETAINING TABS
RIGHT LENS
(1112) 3 of 27
6. Release the drivers sunvisor and passengers sunvisor from the two sunvisor holders.
7. Rotate each sunvisor holders 45 counterclockwise to remove the two sunvisor holders.
8. Pull away the drivers door opening seal from the drivers A-pillar. Gently pull out the drivers A-pillar trim to release the clips.
Q0N2013AG
Rotate.
SUNVISOR HOLDER
SUNVISOR HOLDER
2 SUNVISOR HOLDERS
SUNVISOR
Q0N2014AG
VEHICLE PANEL
CLIP
2 CLIPS
DRIVERS A-PILLAR TRIM
DRIVERS DOOR OPENING SEALPull away.
CLIP
DRIVERS A-PILLAR
4 of 27 AII 46215
9. To prevent the clips from falling into the vehicle body, roll up the shop towel, and insert it between the drivers A-pillar and the dashboard. Take care not to damage the drivers A-pillar.
10. Remove the drivers A-pillar trim. Carefully remove the shop towel and any clips that fell from the drivers A-pillar trim. NOTE: The upper clip will stay in the body.
Q0N2015BG
SHOP TOWEL
DRIVERS A-PILLAR
DASHBOARD
Q0N2016AG
UPPER CLIPDRIVERS A-PILLAR TRIMRemove.
DRIVERS A-PILLAR TRIM
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
11. Remove the remaining upper clip from the drivers A-pillar.
12. Temporarily reinstall the drivers A-pillar trim, and check the overlap between the headliner and the drivers A-pillar trim according to the service manual. Remove the drivers A-pillar trim. Install the new clip (supplied) to the drivers A-pillar trim.
Q0N2017AG
Push 2 tabs.UPPER CLIPDiscard.
DRIVERS A-PILLAR
Q0N2018AG
DRIVERS A-PILLAR TRIM(inside)
NEW CLIP
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
13. Remove the drivers dashboard panel (six clips and unplug the vehicle connector).
14. Remove the drivers air outlet (one self-tapping screw, one retaining tab, and three clips).
Q0N2019BG
VEHICLE CONNECTOR
6 CLIPS
DRIVERS DASHBOARD PANEL
Q0N2020BG
DRIVERS AIR OUTLET
2 CLIPS
RETAINING TAB
SELF-TAPPING SCREW
CLIP
(1112) 5 of 27
15. Remove the drivers dashboard under cover (turn the knob, one clip and one pin).
16. Remove the drivers dashboard lower cover (eight clips and unplug the vehicle connector).
Q0N2021BGPINDRIVERS DASHBOARD UNDER COVER
KNOBTurn.
CLIP
Q0N2022AG
VEHICLE CONNECTOR
8 CLIPSDRIVERS DASHBOARD LOWER COVER
6 of 27 AII 46215
17. Attach masking tape to the upper column cover as shown.
18. Lower the tilt lever, and turn the steering wheel 90 counterclockwise.
19. Using a plastic trim tool, release the lock as shown.
Q0N2023AG
MASKING TAPE
UPPER COLUMN COVER
STEERING WHEEL
Q0N2024BG
PLASTIC TRIM TOOL
STEERING WHEEL
LOCK
UPPER COLUMN COVER
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
20. Turn the steering wheel 180 clockwise. Using a plastic trim tool, release the lock as shown.
21. Secure the upper column cover to the meter panel with the tape.
Q0N2025BG
LOCK
UPPER COLUMN COVER
PLASTIC TRIM TOOL
Q0N2026AG
TAPE
2 RETAINING TABS
UPPER COLUMN COVER
METER PANEL
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
22. Remove the two self-tapping screws from the lower column cover.
23. Remove the lower column cover (one self-tapping screw).
Q0N2027AG
LOWER COLUMN COVER
SELF-TAPPING SCREWS
Q0N2028AG
SELF-TAP-PING SCREW
LOWER COLUMN COVER
(1112) 7 of 27
24. Remove the drivers front door sill trim (two retaining tabs, three clips and two hooks).
25. Pull away the drivers door opening seal, and remove the drivers kick panel (two clips).
Q0N2029BG
2 RETAINING TABS
FRONT
3 CLIPS
2 HOOKS
DRIVERS FRONT DOOR SILL TRIM
Q0N2030AG
DRIVERS DOOR OPENING SEALPull away.
DRIVERS KICK PANEL
2 CLIPS
8 of 27 AII 46215
Installing the Antenna
26. Using the two pairs of needle nose pliers, bend the antenna plate according to the full scale drawing as shown.
Q0N1708CG
ANTENNA
ANTENNA
ANTENNA PLATE
NEEDLE NOSE PLIERS
ANTENNA PLATE
SCALE
9 mm(0.3 in.)
15 mm(0.6 in.)
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
27. Using scissors, cut out the template.
28. Using the strips of masking tape, attach the template to the front windshield. Align the template with the black ceramic paint as shown.
Q0N1701BG
Cut out.
TEMPLATE
SCISSORS
Q0N1702CG
TEMPLATE
MASKING TAPES
Align this end with the end of the black ceramic paint.
TEMPLATE
BLACK CERAMIC PAINT
FRONT WINDSHIELD
CORRECT
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
29. Starting from the antenna end of the antenna cable, wrap three urethane tapes to the antenna cable at the measurements shown.
30. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the antenna will attach.
31. Remove the adhesive backing from the antenna. Insert the antenna plate under the headliner, align the antenna with the template, and attach the antenna to the front windshield. Press the antenna firmly for 30 seconds.
32. Remove the template.
Q0N1703AG
ANTENNA
URETHANE TAPES
20 mm(0.8 in.)
410 mm(16.1 in.)
ANTENNA CABLE
ANTENNA CABLE
20 mm(0.8 in.)
Q0N1704AG
ANTENNA PLATE
ADHESIVE BACKINGRemove.
ANTENNA
TEMPLATE
FRONT WINDSHIELDClean with isopropyl alcohol.
HEADLINER
(1112) 9 of 27
33. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner.
34. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel, where the urethane tapes will attach.
35. Using scissors, cut one urethane tape in half. Secure the antenna cable to the vehicle panel with two cut pieces of urethane tape. Be careful not to crease the headliner.
Q0N1705AG
ANTENNA CABLE
HEADLINER
HEADLINERVEHICLE PANEL
ANTENNA CABLE
Q0N1706AG
VEHICLE PANELClean with isopropyl alcohol.
ANTENNA CABLE
2 URETHANE TAPES
URETHANE TAPECut in half.
10 of 27 AII 46215
36. Route the antenna cable down the drivers A-pillar along the vehicle harness.
37. Secure the antenna cable to the vehicle harness with six wire ties.
38. Route the antenna cable down behind the dashboard.
Q0N1707AG
ANTENNA CABLE
6 WIRE TIES
DRIVERS A-PILLAR
VEHICLE HARNESS
Q0N1709BG
ANTENNA CABLE
TOP VIEW
FRONTSTEERING HANGER BEAM
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
Routing the Engine Starter Harness
39. Plug the three relays into the relay block on the engine starter harness.
40. Using isopropyl alcohol on a shop towel, thoroughly clean the relay block and fuse block where the 3A fuse label and 40A fuse labels will attach.
41. Attach the 3A fuse label and two 40A fuse labels to the relay block and fuse block on the engine starter harness.
42. Route the two 28-pin connectors of the engine starter harness upward as shown.
Q0N1801AG
40A FUSE LABEL
RELAYS
RELAY
40A FUSE LABEL
FUSE BLOCK
RELAY BLOCK
ENGINE STARTER HARNESS
3A FUSE LABEL
Q0N1802BGENGINE STARTER HARNESS
STEERING HANGER BEAM
ENGINE STARTER HARNESS 28-PIN CONNECTOR
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
43. Unplug the vehicle 28-pin connector.
44. Route the engine starter harness 28-pin connectors as shown, and plug the engine starter harness 28-pin connector into the vehicle 28-pin connector.
45. Push the engine starter harness 28-pin connector between the drivers A-pillar and vehicle 28-pin connector as shown.
46. Plug the vehicle 28-pin connector into the engine starter harness 28-pin connector.
Q0N1804CG
VEHICLE 28-PIN CONNECTOR
ENGINE STARTER HARNESS 28-PIN CONNECTOR
Q0N1805BG
VEHICLE 28-PIN CONNECTOR
ENGINE STARTER HARNESS 28-PIN CONNECTOR
TOP VIEW
FRONT
ENGINE STARTER HARNESS 28-PIN CONNECTOR
DRIVERS A-PILLAR
VEHICLE 28-PIN CONNECTOR
(1112) 11 of 27
47. Secure the engine starter harness and the antenna cable to the vehicle frame with one wire tie.
48. Secure the engine starter harness and the antenna cable to the vehicle harness with one wire tie.
Q0N1806BG
VEHICLE HARNESS
WIRE TIE
ENGINE STARTER HARNESS
WIRE TIE
ENGINE STARTER HARNESS
VEHICLE FRAME
ANTENNA CABLE
ANTENNA CABLE
12 of 27 AII 46215
49. Unplug the vehicle 5-pin connector from the fuse box, and plug it into the engine starter harness 5-pin connector.
50. Plug the remaining engine starter harness 5-pin connector into the fuse box. NOTE: Check that the engine starter harness 5-pin connector is securely connected to the fuse box 5-pin connector. A loose connection can cause the engine to stall.
Q0N1807BG
FRONT VIEW
VEHICLE 5-PIN CONNECTOR
ENGINE STARTER HARNESS 5-PIN CONNECTOR
FUSE BOX
FUSE BOX
Plug in here.
UNLOCK LOCK13
12 2Push.Push.Pull.
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
51. Attach the connector clip from the engine starter harness 5-pin connector to the hole in the vehicle panel.
52. Slide the other clip on the engine starter harness onto the vehicle connector. Note the direction and the orientation of the clip.
Q0N1901BG
ENGINE STARTER HARNESS 5-PIN CONNECTOR
FUSE BOX
VEHICLE PANEL
HOLE
CONNECTOR CLIP
Q0N1902BG
ENGINE STARTER HARNESS
CLIP
VEHICLE CONNECTOR
FRONT
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
If the vehicle is equipped with the accessory fog lights, go to step 54; otherwise, continue with step 53.
53. Plug the engine starter harness 4-pin connector into the fuse box. Go to step 56.
Q0N1903BG
FRONT VIEW
FUSE BOX
FUSE BOX
Plug in here.
ENGINE STARTER HARNESS 4-PIN CONNECTOR
(1112) 13 of 27
54. Unplug the fog light 4-pin connector from the fuse box, and plug it into the engine starter harness 4-pin connector.
55. Plug the remaining engine starter harness 4-pin connector into the fuse box.
Q0N1904BG
FRONT VIEW
FUSE BOX
FUSE BOX
Plug in here.
ENGINE STARTER HARNESS 4-PIN CONNECTOR
FOG LIGHTS 4-PIN CONNECTOR
ENGINE STARTER HARNESS 4-PIN CONNECTOR
14 of 27 AII 46215
56. Unplug the vehicle 38-pin connector from the fuse box as shown.
57. Remove the connector cover.
58. Remove the lever from the vehicle 38-pin connector as shown.
Q0N1905AG
VEHICLE 38-PIN CONNECTOR
FUSE BOX
FRONT VIEW
VEHICLE 38-PIN CONNECTOR
CONNECTOR COVER
QA21701AG
VEHICLE 38-PIN CONNECTOR
LEVERRemove.
VEHICLE
38-PIN CONNECTOR
2 TABS
8-PIN CONNECTOR
HARNESS SIDE VIEW
8-PIN CONNECTOR
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
59. Remove the 8-pin connector from the vehicle 38-pin connector (two tabs).
60. Release the retainer from the 8-pin connector.
61. Insert the engine starter harness terminal (orange wire) into the 8-pin connector. Reinstall the 8-pin connector and lever.
62. Secure the engine starter harness to the vehicle harness with an electrical tape.
Q0D1604AK
HARNESS SIDE VIEW
ORANGE WIRE
ENGINE STARTER HARNESS TERMINAL
RETAINER
8-PIN CONNECTOR
ORANGE WIRE
Q0N1907AG
VEHICLE HARNESS
ENGINE STARTER HARNESS
ELECTRICAL TAPE
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
63. Reinstall the connector cover.
64. Plug the vehicle 38-pin connector into the fuse box.
65. Unplug the vehicle 24-pin connector, and plug the engine starter harness 24-pin connector into the vehicle 24-pin connector.
FRONT VIEW
FUSE BOX
FUSE BOX
ENGINE STARTER HARNESS 24-PIN CONNECTOR
VEHICLE 24-PIN CONNECTOR
VEHICLE 24-PIN CONNECTOR
(1112) 15 of 27
66. Slide the clip from the engine starter harness 24-pin connector onto the bottom of the fuse box, then plug the remaining vehicle 24-pin connector into the engine starter harness 24-pin connector.
Q0N2002BG
FRONT VIEW
FUSE BOX
FUSE BOX
ENGINE STARTER HARNESS 24-PIN CONNECTOR
VEHICLE 24-PIN CONNECTOR
FUSE BOX
ENGINE STARTER HARNESS 24-PIN CONNECTOR
16 of 27 AII 46215
67. Secure the engine starter harness to the vehicle harness with two wire ties.
68. Route the engine starter harness under the dashboard and toward the steering wheel.
69. Secure the engine starter harness to the hole in the left knee bolster using the clip on the engine starter harness as shown.
Q0N2003BG
FUSE BOX
ENGINE STARTER HARNESS
VEHICLE HARNESS
WIRE TIES
Q0N2004AG
ENGINE STARTER HARNESS
FRONT
LEFT KNEE BOLSTER
HOLE
CLIPFRONT
ENGINE STARTER HARNESS
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
HARNESS
70. Locate the white tape on the engine starter harness, and loosely secure the engine starter harness to the dashboard with one wire tie at the white tape.
71. Route the engine starter harness up steering wheel as shown.
72. Align the white tape on the engine starter harness with the vehicle clip, and secure the engine starter harness to the vehicle harness with two wire ties as shown.
Q0N2005AG
ENGINE STARTER HARNESS
WIRE TIELoosely secure.
DASHBOARD
WHITE TAPE
Q0N2006BG
ENGINE STARTER HARNESSVEHICLE
CLIP
WHITE TAPE
FRONT
VIEWED FROM BOTTOM
2 WIRE TIES
VEHICLE HARNESS
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
73. Unplug the vehicle 7-pin connector from the ignition switch, and plug it into the engine starter harness 7-pin connector (black).
74. Plug the remaining engine starter harness 7-pin connector (black) into the ignition switch.
75. Secure the 7-pin connectors and engine starter harness to the vehicle harness with one wire tie.
Q0N2007AG
VEHICLE 7-PIN CONNECTOR
ENGINE STARTER HARNESS 7-PIN CONNECTOR (Black)
ENGINE STARTER HARNESS 7-PIN CONNECTOR (Black)
IGNITION SWITCH
STEERING WHEEL
Q090211BK
VEHICLE HARNESS
7-PIN CONNECTORS
WIRE TIE ENGINE
STARTER
(1112) 17 of 27
76. Route the engine starter harness across the steering column area as shown.
77. Unplug the vehicle 10-pin connector from the wiper switch, and plug it into the engine starter harness
10-pin connector.
78. Plug the remaining engine starter harness 10-pin
Q0N2008AG
VEHICLE 10-PIN CONNECTOR
ENGINE STARTER HARNESS
ENGINE STARTER HARNESS 10-PIN CONNECTOR
STEERING WHEEL
WIPER SWITCH
ENGINE STARTER HARNESS 10-PIN CONNECTOR
18 of 27 AII 46215
connector into the wiper switch.
79. Secure the 10-pin connectors and engine starter harness to the vehicle harness with one wire tie.
Q090302BK
IGNITION SWITCH
WIRE TIE
10-PIN CONNECTORS
ENGINE STARTER HARNESS
STEERING WHEEL
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
80. Unplug the vehicle 12-pin connector from the combination light switch, and plug it into the engine starter harness 12-pin connector.
QA20704BG
VEHICLE 12-PIN CONNECTOR
ENGINE STARTER HARNESS 12-PIN CONNECTOR
STEERING WHEEL
COMBINATION LIGHT SWITCH
ENGINE STARTER HARNESS 12-PIN CONNECTOR
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
81. Plug the remaining engine starter harness 12-pin connector into the combination light switch.
82. Secure the engine starter harness to the vehicle harness with two wire ties. Check that the harness is secured without undue strain to the both left and right connector cords. NOTE: Make sure that the connectors and harness are not pinched, or interfering with the steering wheel when adjusted.
Q0N2010BG
ENGINE STARTER HARNESS
VEHICLE HARNESS
WIRE TIES
LEFT CONNECTOR CORD(without undue strain)
RIGHT CONNECTOR CORD(without undue strain)
(1112) 19 of 27
83. Route the antenna cable along the engine starter harness as shown.
84. Secure the antenna cable to the engine starter harness with two wire ties.
85. Loosely secure the antenna cable to the dashboard with one wire tie loosely installed in step 70.
Q0N2303AG
ENGINE STARTER HARNESS
FRONT
LEFT KNEE BOLSTER WIRE
TIE
ANTENNA CABLE
WIRE TIE
ANTENNA CABLE
WIRE TIE
VEHICLE HARNESS
DASHBOARD
FUSE BOX
20 of 27 AII 46215
Installing the Control Unit
86. Using isopropyl alcohol on a shop towel, clean the area where the urethane tape will attach.
87. Attach the one urethane tape to the vehicle unit as shown.
88. Plug the antenna cable and the engine starter harness 28-pin connector into the control unit.
Q0N2305AG
URETHANE TAPE
VEHICLE UNITClean with isopropyl alcohol.
Q0N2306AGENGINE STARTER HARNESS 28-PIN CONNECTOR
ANTENNA CABLE
CONTROL UNIT
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
89. Install the control unit bracket to the control unit.
90. Secure the clip from the engine starter harness fuse block, and the clip from the engine starter harness into the holes in the control unit bracket.
Q0N2307BG
CONTROL UNIT
CONTROL UNIT BRACKET
Q0N2308BG
CONTROL UNIT BRACKET
ENGINE STARTER HARNESS
HOLE
CLIP
HOLECLIP
FUSE BLOCK
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
91. Remove the vehicle flange nut that secures the vehicle bracket.
92. Install the control unit bracket on top of the vehicle bracket and align the control unit bracket with the edge of the vehicle bracket. Reinstall the vehicle flange nut. Install the 8 mm nut (supplied) on top of the vehicle flange nut.
Q0N2309AG
CONTROL UNIT BRACKET
8 mm NUT
VEHICLE FLANGE NUT(reused)
CONTROL UNIT BRACKET
8 mm NUT
VEHICLE BRACKET
VEHICLE FLANGE NUT
VEHICLE BRACKET
VEHICLE PANEL
CONTROL UNIT BRACKET
Align.
(1112) 21 of 27
93. Secure the antenna cable and engine starter harness to the vehicle harness with one long wire tie.
94. Secure the antenna cable to the engine starter harness with one wire tie.
95. Bundle up the excess antenna cable, and secure it to the dashboard with the one wire tie loosely installed in step 85.
Q0N2310BG
ENGINE STARTER HARNESS
FRONT
LONG WIRE TIE
ANTENNA CABLE
VEHICLE HARNESS
WIRE TIE
Q0N2311BG
ANTENNA CABLEBundle up the excess.
WIRE TIEDASHBOARD
22 of 27 AII 46215
96. Using isopropyl alcohol on a shop towel, clean the areas where the urethane tapes will attach.
97. Attach the two urethane tapes to the inside of the lower column cover.
98. Open the hood. Using isopropyl alcohol on a shop towel, thoroughly clean the hood where the caution label will attach.
99. Remove the adhesive backing from the caution label, and attach the caution label to the hood in the area shown.
Q090601AK
Clean with isopropyl alcohol.
URETHANE TAPES
LOWER COLUMN COVER(inside)
Q0N2011AG
ADHESIVE BACKINGRemove.
CAUTION LABEL
HOODClean with isopropyl alcohol.
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
100. Check that all wire harness and cables are routed properly and that all connectors are plugged in.
101. Reinstall all removed parts.
102. Reconnect the negative cable to the battery.
103. Check the operation of the headlights and wipers.
104. Press and hold the radio power button for two seconds to restore the radio and navi (if equipped) system functions.
105. Reset the clock on vehicles without navigation.
106. Proceed to the REMOTE ENGINE STARTER REGISTRATION (Page 23) and FUNCTION CHECK (Page 26).
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
REMOTE ENGINE STARTER REGISTRATION
1. Acquire the PCM Code from ISIS.
2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the on (II) position.
3. Start the HDS, and click the car icon.
4. Input the VIN and other required information into the HDS, then click the check button.
792901AH
CAR ICON
752502AS
Input the VIN and other required information. CHECK BUTTON
(1112) 23 of 27
5. Select Honda Systems, then click the check button.
6. Select R/C ENG STARTER and click the check button.
752503AS
Select Honda Systems. CHECK BUTTON
752504AS
Select R/C ENG STARTER. CHECK BUTTON
24 of 27 AII 46215
7. Check that REMARKS is shown, then click the check button.
8. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button.
752505AS
Check that REMARKS is shown.
CHECK BUTTON
752506AS
Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT.
CHECK BUTTON
(1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
9. The following message will display: Obtain PCM code (IMMOBILIZER PCM CODE) from iN. This vehicles VIN will be required to obtain the password (USA). Click on the check button.
10. Input the PCM Code, then click the check button. NOTE: To ensure security, the PCM code (password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same.
752507AS
Obtain PCM-code message.
CHECK BUTTON
752509AS
Input the PCM Code.
CHECK BUTTON
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215
11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click on the check button.
12. The following message will display: Check that the engine can be started by the Transmitter. Click on the check button.
13. Perform the function test on page 26, then disconnect the HDS.
752510AS
The registration of the Remote Control Engine Starter Unit has been completed.
CHECK BUTTON
752511AS
Check that the engine can be started by the Transmitter.
CHECK BUTTON
(1112) 25 of 27
FUNCTION CHECK
Operating Conditions
The hood is closed
The shift lever is in park
The key is out of the ignition and the key is outside the vehicle
All doors and tailgate closed and locked
Inspection
1. Press the command button, and then, within 1 second, press the start button on the transmitter.
The engine should start if all operating conditions are met.
Does the engine start?
2. Press the command button on the transmitter and, within 1 second, press the stop button. The engine should stop.
Does the engine stop?
3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:
NOTE: After each test the ignition key must be cycled, or the drivers door must be opened and closed.
Move the shift lever out of the P position.
Unlock or open the doors or the tailgate.
Open the hood.
Insert the key in the ignition.
Press on the brake pedal.
Does the engine stop after each of these tests?
4. Check that the power windows and the moonroof do not function when the engine is started with the transmitter.
5. Start the engine again, press the command button on the transmitter two times and check the vehicle condition on the display.
6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away and in direct sight.
7. Insert the key in the ignition and start the engine, check the operation of the headlights and wipers.
Yes - Operation is normal.
No:
Make sure all Operating Conditions are met.
Check the engine starter harness connections.
Connect the HDS and check for an indicated failure.
(Refer to the appropriate service manual for details.)
Yes - Operation is normal.
No - Check the engine starter harness connections.
Yes - Operation is normal.
No - Check the engine starter harness connections.
732904AY
DISPLAY
START BUTTON
COMMAND BUTTON
STOP BUTTON
TRANSMITTER
26 of 27 AII 46215 (1112) 2011 American Honda Motor Co., Inc. All Rights Reserved.
How to Program an Additional Transmitter
1. Connect the HDS to the data link connector.
2. Start the HDS and click on the car icon.
3. Input the vehicles VIN and other required information.
4. Select Honda Systems.
5. Select R/C ENG STARTER.
6. Select REGISTER NEW TRANSMITTER.
7. When Ready to program the new transmitter shows, select ENTER.
8. Press and release the Command button.
9. Press and release the Stop button.
10. Perform the function check on both transmitters.
NOTE: Only 2 remotes can be stored in the systems memory.
2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46215 (1112) 27 of 27
Button1: Button2: Button3: Button4: Button5: Button6: Button7: Button8: Button9: Button10: Button11: Button12: Button13: