1-800-597-3921 for Nexus Application Support. For additional suggested Speeds & Feeds for milling or turning inserts, go to http://delivr.com/1kpmp

! for best results, use these SuggeSted Starting parameterS.speeds & feeds for AoMt123608Petr-lt30 (part no. 3153311)

min max min max min max D.O.C. Feed Vc1 125 HB 0.433 0.009 1080 8202 190 HB 0.433 0.009 980 7203 250 HB 0.433 0.009 820 6506 180 HB 0.433 0.007 490 780 650

4,6 230 HB 0.433 0.007 490 680 5905,7 280 HB 0.433 0.006 420 620 4908 350 HB 0.433 0.006 420 550 450

10 220 HB 0.309 0.006 290 490 0.005 42010 280 HB 0.309 0.006 290 420 0.005 39011 320 HB 0.309 0.005 190 360 0.004 32011 350 HB 0.309 0.005 190 290 0.004 26014 180 HB 0.433 0.004 0.007 620 820 72014 240 HB 0.433 0.003 0.006 520 680 62014 290 HB 0.309 0.005 420 32014 310 HB 0.309 0.005 390 29012 200 HB 0.433 0.007 490 680 0.079 0.005 62013 42 HRc 0.309 0.006 290 490 0.059 0.004 42015 150 HB 0.433 0.009 780 65015 200 HB 0.433 0.009 720 59016 250 HB 0.433 0.009 620 520

17,19 150 HB 0.433 0.008 650 59017,19 200 HB 0.433 0.008 590 49018,20 250 HB 0.433 0.008 490 42031,32 Incoloy 800 240 HB 0.309 0.005 140 100

33 Inconel 700 250 HB 0.309 0.005 140 9034 Stellite 21 350 HB 0.309 0.005 140 9036 TiAl6V4 - 0.309 0.006 130 210 0.005 18037 T40 - 0.309 0.005 90 180 0.004 13038 45 HRc 0.155 0.005 260 0.039 0.004 19038 50 HRc 0.093 0.004 220 0.030 0.003 18038 55 HRc 0.046 0.004 190 0.020 0.003 160

Chilled Cast Iron 40 Ni-Hard 2 400 HB 0.020 0.124 0.003 0.005 130 260 0.030 0.004 160White Cast Iron 41 G-X300CrMo15 55 HRc 0.020 0.046 0.003 0.004 90 190 0.020 0.003 130

NF Al (>8%Si) 12 25 AlSi12 130 HB 0.020 0.433 0.005 0.009 650 1310 0.079 0.006 910

0.020

0.020

0.020

0.020

0.020

0.020

0.020

0.020

0.020

0.020

0.020

Vc [sfm]Material Group Gr. N VDI Group Material Examples* Hardness

D.O.C. [inch] Feed [inch/tooth]

St

eel

Non-alloyed 1 C35, Ck45, 1020, 1045, 1060, 28Mn6

Low alloyed 2 42CrMo4, St50, Ck60, 4140, 4340, 100Cr6

High alloyed 3 X40CrMoV5, H13, M42, D3, S6-5-2, 12Ni19

Stai

nles

s St

eel Austenitic 4 304, 316, X5CrNi18-9

Duplex 5 X2CrNiN23-4, S31500

Ferritic & Martensitic 6 410, X6Cr17, 17-4 PH, 430

Cast

Iron

Grey 7 GG20, GG40, EN-GJL-250, No30B

Malleable & Nodular 8 GGG40, GGG70, 50005

X100CrMo13, 440C, G-X260NiCr42

Hard

ened

Mat

.

Steel11

High

Tem

p.Al

loys

Fe, Ni & Co based 9

Ti based 10

0.004

0.003

0.005

0.004

0.003

0.003

0.003

0.003

620

220

490

320

80

130

0.004

0.005 0.079

0.079

0.059

0.079

0.079

0.059

0.079

AOMT123608PDTR-LT30

0.059

0.006

0.005

0.005

0.004

0.006

0.005

0.004

0.059

SuggestedStarting Parameters